hi,
I don't get my expressions Pedal work. Not on my FCB1010 with Un0 and not when connecting direct to the Kemper via Pedal input.
Any tips or tricks?
regards
bern
hi,
I don't get my expressions Pedal work. Not on my FCB1010 with Un0 and not when connecting direct to the Kemper via Pedal input.
Any tips or tricks?
regards
bern
Welcome!
Let's begin with the FCB and its pedals first.
Did you do a pedal calibration per the instructions in the FCB manual?
Are you using UnO or UnO4Kemper?
The UnO4Kemper is pre- programmed, the UnO needs to be programmed manually for pedal use.
Ive been using my FCB1010 w/stock UNO with my KPA for a couple of years and for the most part it's worked pretty flawlessly. But today I tried using the WA to pitch function in the KPA and it did not work. In the systemsettings you can see the pedal is functioning, but the pitch didn't change. Was trying to use the factory octive down profile. ANty help would be appreciated I can't figue out what i'm doing wrong?????
Ive been using my FCB1010 w/stock UNO with my KPA for a couple of years and for the most part it's worked pretty flawlessly. But today I tried using the WA to pitch function in the KPA and it did not work. In the systemsettings you can see the pedal is functioning, but the pitch didn't change. Was trying to use the factory octive down profile. ANty help would be appreciated I can't figue out what i'm doing wrong?????
Just for clarification: is a pedal pitch effect present in the rig, and is it switched ON? Otherwise wah to pitch won't work.
yes I was trying to use the -12 rig which I think is one of the factory rigs
But does the -12 contain a pedal pitch or an octaver?
thanks fo your querry,it contains a pedal pitch
I'll get a chance to fool with it some more tonight, hopefully It's just something foolish i'm doing.
Yes please, I'm a bit out of ideas...
just a dumb joining in: CC assignement?
I hooked my two exp pedals via the exp pedal ports of my rocktron all access, and after assignement flawlessly........don't know though how the FCB works compared to rocktron.
The FCB1010 Uno4K is pre-programmed, you cannot assign CC's to the pedals manually.
ah, ok...didn't know it
michael
I'm using stock UNO chip. I'll finally have time after work today to work on it. Thanks for the sugestions.
I do know I have it set WA to Pitch. It works flawlessly with WA
Well If I can figure out how, I guess i'll open a support ticket. I have no problem with the FCB1010 working the wa settings. But the pitch setting does not work. I have 2 rigs that both have the pitchpedal set to -12 . With the effect turned on and the pedal set wah to pich it just doesn't work..
Have you re-calibrated just once?
I had to do this a few times with my FCB because of pedals behaving improperly.
Solved the pedal pitch not working.
I recalibrated the FCB pedals a couple of times to no avail, while waiting for a response from Kemper support.
I got a very quick response from Burkhard ( thank you very much)on the matter. He pointed out that the pedal must start off at "0" to activate pedal pitch, which makes perfect sense but I had not read that anywhere.
So I recalibrated carefully again and again no worky.
I later hooked up FCB to Ripworx programmer and discovered the pedal had a default setting of "1" changed this to "0"and problem solved'..... Now I'm a happy camper er/ Kemperer
Thanks to all that tried to help and thanks to Burkhard for the all important info on having to start at zero. Saved me tearing open my FCB
Still don't understand what the culprit was and the default setting of 1. Calibration should make sure heel down is 0 and to down is 127. am I missing something?
Still don't understand what the culprit was and the default setting of 1. Calibration should make sure heel down is 0 and to down is 127. am I missing something?
When I loaded the MIDI sysex from the pedal into the Ripwerx programmer, It showed a low setting of 1. I changed this to "0" on all patches and it cured it, when I reloaded the MIDI sysex back into the FCB.
I had never changed these settings from when I origionaly installed the UNO chip and guess that it just allways at "1" and it was never an issue befor. Anyway it works now
Good to know if I ever encounter problems, thanks!