Are Looper functions avalaible in the last firmware update ?
An could we have a recap of the different NRPN command to control the lopper, by the KPA Team or a liste of CC events ?
"YES"
Thank you Kemper co. very much.
Are Looper functions avalaible in the last firmware update ?
An could we have a recap of the different NRPN command to control the lopper, by the KPA Team or a liste of CC events ?
"YES"
Thank you Kemper co. very much.
Looper working with 3.0.2?
Working by control change? I find nothing on manual
Working by control change? I find nothing on manual
The looper functions are undocumented and unsupported at this time.
Please read this thread from the beginning.
NRPN are working now:) Thanks KPA Team.
@DamianGreda - you may want to make a new "Tips and Tricks" post, to explain how to do this
@DamianGreda - you may want to make a new "Tips and Tricks" post, to explain how to do this
Good idea
I just tried your html page and it works fine with the new firmware, thanks!
I'm going to try to make a looper preset for my foot controller next time I'm using it :).
I've been using it for the past couple of days via CC# - today i went live with it for the first time and it works perfectly.
Important addition to the arsenal if the Kemper is an all-in-one guitar tool.
You think there's a chance we'd get the looper position (pre/post) option available to us? Or am i pushing it?
It's currently locked away in the 'remote' section of the settings.
I've been using it for the past couple of days via CC# - today i went live with it for the first time and it works perfectly.
Important addition to the arsenal if the Kemper is an all-in-one guitar tool.
You think there's a chance we'd get the looper position (pre/post) option available to us? Or am i pushing it?
It's currently locked away in the 'remote' section of the settings.
Happy to hear that looper works for you:)
You can always go to debug mode by holding system button for 4 seconds -> go to the page where is USB Stick Connected (and list of other things) -> Scroll down to the #connected Remotes and change value to bigger then 0.
Now you can go to the remote settings and change looper location:)
I think there is NRPN for looper location but i dit't foud it( i've not searched it). Almost all the function of the KPA are accesible via NRPN (sysex) .
@timo can you point us in this please?
You think there's a chance we'd get the looper position (pre/post) option available to us? Or am i pushing it?
You can use Looper position option even without changing anything in debug menu. It works right away on the page 4 in the system settings. It's the fourth soft button (rightmost). The page is grayed out, but still working.
I've been using it for the past couple of days via CC#
Did you mean NRPNs? Or are you using that html/JS converter?
They said they would do this. Good follow through. Go Kemper!
Tutorial for those less up to speed on midi would be great
You can use Looper position option even without changing anything in debug menu. It works right away on the page 4 in the system settings. It's the fourth soft button (rightmost). The page is grayed out, but still working.
That's good to know, i never considered trying. Thanks!
As for your question, i'm using my own MIDI board. NRPN is essentially a set of 4 CC# in a row, so i'm treating them as such since it is easier to implement on my particular system.
Tutorial for those less up to speed on midi would be great
Do you have a programmable MIDI controller? One that can send more than one message per-button-press?
with the uno chip for fcb1010 I can only send 2 cc at the time
with the uno chip for fcb1010 I can only send 2 cc at the time
Indeed this is true. When we tested the looper NRPNs I had to switch two buttons for one looper command. That was the tapdancing John Huldt was talking about at NAMM.
A tutorial could be fantastic.. i have a gordius little giant