EurekaPROM 3 (w/ looper mode)

    Anyone tested it yet?


    Found this on their site (http://www.eurekasound.com/eurekaprom/pa:(


    Overview
    Five Modes, easily switched between using the Up/Down pedals:


    - New in EurekaPROM3.0! Effects Mode: Turn individual effects on/off in stompbox-like fashion, with state reflected on the pedal LED. Plus tuner access, with note reflected on FCB1010 7-segment display!
    - Presets Mode: Easily enter Performances 1-125, Slots 1-5, & Presets 1-128.
    - Favorite Presets Mode: Allows you to store and recall your 10 favorite presets with the push of a pedal!
    - New in EurekaPROM3.0! Specials Mode: Looper, plus change the expression pedal definition to modify 8 effects parameters!
    - Effects & Presets Mode: Access Effects mode pedals 1-5 & Favorite Presets pedals 6-10 in one layout


    Expression Pedals programmed for 10 effects & volume. MIDI activity LED. And waterproof labels!

    Thanks for the heads up. Just ordered. Been using Eurekaprom 2 with my FCB1010 for a couple years now. No programming, Plug&Play, easy access to presets, performances, tuner, effects on/off, wah, and expression pedals. Love it. Looking forward to the new Looper mode in Eurekaprom 3.

    Installed the Eurekaprom v3 in my FCB1010 last night. Took about 20 min total. Now able to use the looper through my FCB1010 footcontroller. In Kemper mode, the Eurekaprom gives you instant access to 5 pedal modes instantly accessed via the up and down pedals on the FCB1010:


    [Blocked Image: http://www.eurekasound.com/_/rsrc/1382474275090/eurekaprom/pa/PA%20EF.png]


    1) EF: Effects (switch effects on and off)


    Notes:
    Turn Effects on/off!
    With 2 MIDI cables connected (FCB MIDI out-to-KPA MIDI in & FCB MIDI in-to-KPA MIDI out), effects state for pedals 1-8 is automatically updated on the pedal LEDs, plus tuner information displayed in FCB1010 7-segment display.
    With 1 MIDI cable connected (FCB MIDI out-to-KPA MIDI in), the LEDs do not automatically update, but they still have state, three in fact: off, on, blip (for unknown effects state).


    [Blocked Image: http://www.eurekasound.com/_/rsrc/1382310377842/eurekaprom/pa/PA%20Pr.png]
    2) Pr: Presets (scroll through presets and performances)


    Notes:
    Enter Performances 1-125, Slots 1 through 5 using pedals 1-7.
    Enter Presets 1-128 using pedals 8-10.
    Press & hold pedal 10 to engage Instant Send, which will send the preset program change command on value change.

    [Blocked Image: http://www.eurekasound.com/_/rsrc/1382310377842/eurekaprom/pa/PA%20FP.png.1379358936539.png]
    3) FP: Favorite Presets (assign 10 presets as favorites)


    Notes:
    Store 10 of your favorite Presets for 1 press recall!
    To store a Preset:
    In Pr mode, select preset via the EurekaPROM-enabled FCB1010.
    Press & Hold the UP pedal until the 7-segment display begins to flash FP.
    Press the pedal you wish to store the Preset. The 7-segment display will flash when stored.
    To recall a Preset, press and release the pedal of your choice.


    [Blocked Image: http://www.eurekasound.com/_/rsrc/1451503994375/eurekaprom/pa/PA%20SP.png]
    4) SP: Specials - Expression Pedal CC Assignment (Looper mode)


    Notes:
    Pedals 1-6 control the Kemper looper.
    Pedals 7 & 8 set the left expression pedal to Wah & Pitch respectively.
    Pedals 9 & 10 set left expression pedal to Delay Mix, Delay Feedback, Reverb Mix, Reverb Time, Gain, and Monitor Volume.


    [Blocked Image: http://www.eurekasound.com/_/rsrc/1382310377842/eurekaprom/pa/PA%20EP.png]
    5) EP: Effects & Presets (botttom row of buttons fx on off / top row select presets)


    Notes:
    To get to EP mode:
    Go to EF mode.
    Press & Hold the UP pedal until both the EFfects LED & Favorite Presets LED are both lit.
    Pedals 1-5 are from EFfects mode.
    Pedals 6-10 are from FP mode.


    MIDI Activity LED


    In 1-cable mode, the LED is on when MIDI is sent, off otherwise.
    In 2-cable mode, the LED is off when MIDI is sent/received, on otherwise.


    You can also switch the same eprom to any of the following configurations


    Configurations
    A3: AdrenaLinn III
    PA: Kemper Profling Amp
    VA: V-Amp Series
    VB: Bass V-Amp Series
    11: Eleven Rack
    G-: TC Electronic G- series
    FA: Fractal Axe-FX II
    Po: POD series
    bo: BOSS/Roland devices
    PP: Programmable, for all other effects
    IO: Input/Output mode for programmers

    You may want to wait before purchasing. I just emailed the folks at Eurekaprom last week about adding access to the new morphing feature in the KPA. They responded that they are working on it.

    <p>ok, thanx for responding</p>


    <p>By the way, the looper seems to be tricky with the level balance between overdubs&nbsp; I've got a loud &quot;pumping effect&quot; : unsable !</p>


    <p><br />
    &nbsp;</p>