So I will be getting an Orange PCB212 to jam with the kemper finally
My only concern now is getting a good but no so expensive power amp.
What do you guys recommend? I'm trying to maintain it below $300...
Thanks!
So I will be getting an Orange PCB212 to jam with the kemper finally
My only concern now is getting a good but no so expensive power amp.
What do you guys recommend? I'm trying to maintain it below $300...
Thanks!
I would try this.... https://www.sweetwater.com/store/detail/NU1000DSP
I've had a Crate Powerblock and ISP stealth. I tested them against the Behringer and the Behringer won. If you need more go to the 3000DSP. There are other options, but I don't think you will be disappointed.
Reverb, Ebay or Craigslist will yield better pricing.
Thanks for the suggestion! This looks promising.
Will this be enough in the event I jam with another guitarist and drummer?
I also wanna add that the cab is rated at 16 Ohms, dont know how much that impacts the power amp decision
Make a cable to use in bridge mode. I'm not sure how loud everyone is that plays with you. I have the powered head now which is 600 watts so I would suggest that it should be more than ample......but you might be one of the few that likes it louder than me
If you are unsure go with the 3000. You also don't need the DSP model so check pricing on the different versions. I think I got a 1000 for $125.
Just "regular" loud I'd say haha nothing too extreme
Can you elaborate on the "make a cable to use in bridge mode"?
Thanks again
The outputs are speakon only and not dual 1/4" & speakon. In order to run bridged (highest wattage) you will need to buy a speakon connector and a speaker cable and make one with the correct wire configuration. They are screw in so it's not difficult. That is the least expensive way anyhow. You can also purchase a speaker cable with speakon end wired for bridge and 1/4"...that is fastest, but it's very easy. A regular speakon configuration will work as well, but you would yield lower wattage.
EHX Magnum 44. Fits in your pocket and gets as loud as a 100W tube amp. I'm not even joking. You can drown a loud drummer with this thing.
Only thing to be aware about it is that all of the clean volume is between 0-4 on the dial, rest just adds compression (by design to emulate a tube amp).
EHX Magnum 44. Fits in your pocket and gets as loud as a 100W tube amp. I'm not even joking. You can drown a loud drummer with this thing.
Only thing to be aware about it is that all of the clean volume is between 0-4 on the dial, rest just adds compression (by design to emulate a tube amp).
That thing is great, I'd been using this for quite a time. Really can stand against a drummer. If only there wasn't that huge power brick...
That thing is great, I'd been using this for quite a time. Really can stand against a drummer. If only there wasn't that huge power brick...
Yeah it's great fun to show up to a band rehearsal and watch peoples faces when you turn it on.
Check this one:
https://www.electromarket.co.u…-digital-amplifier-2x600w
I play now the Kemper with a thomann.de/gb/harley_benton_gp…rch_rslt_gp+400_319961_12 and a 1x12 cab with a Eminence Swamp Thang.. Sounds killer
I play now the Kemper with a thomann.de/gb/harley_benton_gp…rch_rslt_gp+400_319961_12 and a 1x12 cab with a Eminence Swamp Thang.. Sounds killer
what kind of cable do i need to run this amp in bridge mode?? because it seems to need to plug two jack in bridge mode. can i just set it to bridge mode and plug just one jack in the output??
thanks
Only one cable is needed. There is the possibility to set a little switch to bridge mode. The you can just use one cable and set the desired volume on the left channel only what is then representing the "switched channels". Two cables only in stereo. You can trust it works like a charm. And sounds killer.....
Did you use this power??
This is the one - yes. And I bought 6 of these chicken head knobs
https://www.thomann.de/de/part…enhead_potiknob_black.htm
for better visibility and look
Did you use this power??
Yes, Sir. But I'm going direct to FOH now and for monitoring I use inears.
Only one cable is needed. There is the possibility to set a little switch to bridge mode. The you can just use one cable and set the desired volume on the left channel only what is then representing the "switched channels". Two cables only in stereo. You can trust it works like a charm. And sounds killer.....
thanks!!!