QuoteSo it might not fit in the Namba bag, but into a 19" Rack....
Love that it fits in a rack, perhaps Velcroed into the back lid, if not too deep for the lid.
QuoteSo it might not fit in the Namba bag, but into a 19" Rack....
Love that it fits in a rack, perhaps Velcroed into the back lid, if not too deep for the lid.
Agreed. The jacks on the back of the Profiler can be used for pedals or switches. It makes sense that these could be used the same way.
This
Display MoreSorry everyone - I just wrongly read the scale from the measurment tool. RJ45 slot inner width = 11.9mm (not 9.3mm as I posted earlier) by design.
[Blocked Image: http://s12.postimg.org/tqmtowpkd/rj45.jpg]
I magnified the original picture of KPA Remote (which is 2048px in width) by 4 times in MS Paint and tried to match pixels while measuring RJ45 inner slot by blue line, so the width beign 35x RJ45 slot should be fine. So the size of KPA remote should be:
Width = 41.5cm
Height = 7.5cm
[Blocked Image: http://s7.postimg.org/dmdsb7l4b/kemper_remote.jpg]
32cm was really doubtful for me just it would look kinda toyish
PLease, do you have a pic of the top of the KFC ? thanks roger
QuotePLease, do you have a pic of the top of the KFC ? thanks roger
No But browsing photos on Kemper's facebook I found THYYYYZZZZZ
[Blocked Image: http://s14.postimg.org/s5qauh581/413615_350944834921846_1466412834_o.jpg]
OK here is another bit of investigation
LOOPER SWITCH LOCATION (right of center on the upper side)
[Blocked Image: http://s1.postimg.org/o0ac032sv/2015_01_03_225042.jpg]
Another visualisation:
[Blocked Image: http://s28.postimg.org/rlh1zpy19/10899993_1016710705011919_3241156546484186712_o.jpg]
Hahaha! Hey Skoczy, it really seems you're having fun
Hahaha! Hey Skoczy, it really seems you're having fun
Yeah, I like to investigate to get to the goodies
No, you're right, you're definitely right!
Well, it seems that the smaller signs should be of help... "contrast" and "network" should label the corresponding objects on the back of the unit, so I don't think it could be the leftmost one (there would be labels for the 1/4" sockets near it IMO).
Does this make any sense?
Well, it seems that the smaller signs should be of help... "contrast" and "network" should label the corresponding objects on the back of the unit, so I don't think it could be the leftmost one (there would be labels for the 1/4" sockets near it IMO).
Does this make any sense?
Yes Network and Contrast are the labels corresponding to the back of the unit. This previous image was kind of joke I don't know why it was deleted from my post. Nevermind.
Skoczy,
Now, figure out where the LCD goes - you can start to "fill in the blanks" of a view from above
Skoczy,
Now, figure out where the LCD goes - you can start to "fill in the blanks" of a view from above
For me it seems easy Any opinions?
[Blocked Image: http://s13.postimg.org/4tt3oxyl3/kemper_lcd1.jpg]
I'd agree, Watson
I'd agree, Watson
Sherlok, are you comparing to the unit you POSSES? hahahahhahahaha
Here is original design on the >>> first page of this thread <<< so we can see that ethernet connection and EXP3 EXP4 were replaced.
[Blocked Image: http://s12.postimg.org/rd9cjbycd/kmepr2.jpg]
I'm wondering about that Looper.
If the looper option is only with Remote - so what Remote is doing?
1.Reciving audio data via Ethernet and looping them in internal RAM
or
2. just sending the signal data about looping to the KPA DSP?
If 1. Is the answer - there will be possible to send digital data to the PC via ethernet cable in the future.
There also will be possible to add expansion AD/DA conversion to the remote for FX loop purpose.
Sherlok, are you comparing to the unit you POSSES? hahahahhahahaha
Hahaha not really, but that small "bar" looks either like an elevated display plate or a protective tool for the display. Just makes sense to me
I'm wondering about that Looper.
If the looper option is only with Remote - so what Remote is doing?
1.Reciving audio data via Ethernet and looping them in internal RAM
or
2. just sending the signal data about looping to the KPA DSP?
A few months ago, a user had involuntarily hit a combination of buttons that had activated a phrase repeat on his Profiler. So I'd go for your second entry. Just a guess tho.
Please do not ask where I got this picture from....
JUST EAT IT !!!!!![Blocked Image: http://rs156.pbsrc.com/albums/t25/lee_taeho/headbang.gif~c200] [Blocked Image: http://rs120.pbsrc.com/albums/o175/MattLittleJ/64174001gIW7Nt7sheadbang.gif~c200]
[Blocked Image: http://s27.postimg.org/rnofs8xlv/kemper_teaser_newest.jpg]
Very creative! You filled in the blanks
Shut the froooont door!!! WOW!! Uuuuh anybody got an extra cigarette?? I need one now thanks to that pic...LMAO!!!
Wow.
This is what fun can lead to