Request in whith my band's profile ASTORIA.
Posts by VITCHPAT1
-
-
Thanks you All
Christoph Kemper was talking about a community of users sharing their rigs and profiles. Well he have it!
Now can we have the fix for the bugs?
.... please
-
Yeah bridged at 8 ohms is 800w. Bridged at 16 ohms gives about 500w. Obviously that's for the GT800FX. The GM50 is mono to start with! Just think of it as one half of a GT800.
Half price also then
-
Well that issue was not reported in 1.05 so perhaps the issue occured during the update of the firmware.
-
It might sound crazy but have you try to go back to 1.05 and then to 1.06 again?
-
I did not had the time to try your great profile before, so many good profiles, so little time to play them all
Many thanks Feck
-
That's really important right here. So, you went from 1.0.4 to 1.0.6? You skipped 1.0.5. did I get this right? This might be important for support - so they know where to look
Yes I have skip 1.05
Do you have a EQ in your rig? Have you tried to bypass it, save the rig and try again to switch between rigs. Perhaps the EQ settings are not recall properly
-
That's interesting. Did you upgrade from 1.0.4. to 1.0.5 and then to 1.0.6? Or did you skip an update?
I did skip the update as I had several gigs planned and did not what to have issues with the wha cc...
-
I never updated to 1.05, I went straight from 1.04 to 1.06...no problems here.
One noticeable change between 1.04 and 1.06, there seems to be a difference in master volume, I set my MV a little higher than I did using 1.04.
So, as you can imagine, I'm not understanding this thread at all.
Well we are two then
Difference in volume but no other issues here
I can however hear the difference on the sound samples posted. I have the same issue on an FX Ultra but just when you switch it on a preset. It must come from 1.05 as I have tested again and no issue here.
-
that's a bit sad, a quest is over...
-
-
And a free
[Blocked Image: http://idata.over-blog.com/0/31/32/44/Autres/kfc-bucket-of-chicken.gif]
For all
-
I was thinking about:
[Blocked Image: http://www.ikonet.com/fr/ledictionnairevisuel/images/qc/scie-a-guichet-273070.jpg]
But if you recommend a bigger model
-
Unfortunatelly not it is a closed back
-
Well guys I can tell you that IMHO the Kemper + GT800 FX + TT CAB loaded with EVM12l is a fantastic combinaison ("cab bypass" set as a cab on the KPA)
Had my first reversal last WE with this configuration and WHAOUUU!!!
So if Matrix could do an Amp that fit in the back of my KPA I will buy it. -
Some artefacts on high strings and high gain profiles. No issues on low strings and clean rigs. FW 1.04, VGS guitar with EMG Lukater kit.
-
Hi guys, I am Pat. I am on day 3 of my kemper life.
I have spend the last 48 hours on browsing throught the profiles and I was thinking also on doing a top 10-20 but come on, how can you do that?!
How can you say well for clean I am going for the Fender 65 from Gene, or the clean Riveira 100, or this other Tills profile etc etc..
I now that for our set I will only have to take 2 or 3 amp and cabs and honestly whilst I had now issue with the Ultra, this is my biggest problem now with the kemper as I want them all...
-
I am finally "Kemperised" and have tried the DT990 but whilst it is great for clean sounds as soon as I have started exploring the chuga chuga rigs the sound is fizzy. I think that this model is too sensible for the high gain stuff. I took a basic Sony MDR and the sound is just perfect.
-
Great many thanks
-
The DT990's are 600 ohm impedance. It'd be helpful to know what impedance the KPA kicks out, if anyone knows...
Hum as per the specs sheet it is a 250 ohms impedance.