Hi nwmusic32,
the USB-B port has some flexibility, it should clearly not have a lot of movement. Please open a support ticket https://www.kemper-amps.com/contact
Thank you.
Hi nwmusic32,
the USB-B port has some flexibility, it should clearly not have a lot of movement. Please open a support ticket https://www.kemper-amps.com/contact
Thank you.
BayouTexan 😂😂😂 yeah, dust is dust, but the complaint is about the non-sealed screen, or at least some easy way to clean it without voiding my warranty... Because I assume that if I open it for cleaning the screen, warranty will be void, right HELL-G ?
javi garcia guitar correct, opening the unit will void the warranty. Pet hair and dust are electrostatic and thus tend to get almost everywhere.
We do not have many complaints regarding dust behind the screen, though. So I take this as bad luck. Please open a support ticket if you want to have it fixed. Thank you.
javi garcia guitar It seems that a hair has gotten into the Profiler. I see a similar one on the housing of the Profiler, i assume you have a cat?
Please note that the housing of your Profiler is not hermetically sealed and that dust or hair can enter through the venting holes or other gaps.
Please open a support ticket in case you need further assistance. Thank you.
SpaceIceCream1987 Connect Monitor Output to the Camplifier Input. Camplifier Speaker Output goes to Kabinet Input.
Activate Kemper Kone in the Output menu.
arminwipperfuerth Hallo Armin, du hast anscheinend den Main Output auf DEL/REV Wet gestellt. Im Output Menü Output Source für Main Output auf Master Stereo (Monitor Output auf Master Mono) stellen, dann sollte es wieder gehen.
RosboneMako Did you ever contact support? https://www.kemper-amps.com/contact
Please open a support ticket here: https://www.kemper-amps.com/contact
In this case..is it needed to trim down the clean sense?
Clean Sense only needs to be trimmed in order to obtain the optimum DI level when recording the guitar.
you mean that i should set the daw fader in order to avoid clipping kemper?
Yes.
The Main Manual provides all information on this matter:
Step two: DI output leveling and recording
To adjust the DI output level, enter the Input Section and select the “Clean Sens” parameter. You might have used this control already, as it is used to adapt the individual level of your guitar to the overall volume level of the Rigs and PROFILEs as described in the chapter INPUT button. Adjust the “Clean Sens” parameter to a level where clean sounds have the same perceived loudness as distorted sounds; in doing so, you will have adjusted the dynamics of your instrument to match the digital headroom of the PROFILER perfectly. The output assigned to “Git Studio” is perfectly leveled at the same time.
While the ability to adjust the level of the amp is a convenient feature, it becomes critical when recording the DI signal, as it helps to keep the noise floor down. When you later reamp this signal with a high gain setting, the noise floor of the recording will be significantly amplified. The INPUT LED provides a further gauge for correct leveling: the LED should flash yellow when you hit the strings hard - try to avoid deep orange or red color.
Step four: reamping input leveling
For an optimum signal-to-noise ratio, leveling the reamping input is just as critical as leveling the pure instrument output. The leveling is done by the output level of the recording device; it cannot be adjusted in the PROFILER. The S/PDIF signal can only be adjusted in the sending device by definition.
Play your guitar through the armed track or play back a previously recorded track. Watch the INPUT LED while you adjust the output volume on the recording device. The LED should turn to yellow when the strings are struck hard,
but no further. This is all you need to do, so long as the Rig you are reamping has no distorting amp or effect in the signal flow.
If you reamp a distorting Rig, you might notice that the amount of distortion still differs from the original, despite following the above procedure. This is a natural consequence of the correct leveling of input and output: the leveling is made to achieve an optimum signal-to-noise ratio but does not deal with the preservation of the original instrument level. This is what the parameter “Reamp Sens” is for - simply dial the desired amount of distortion via ”Reamp Sens” - and you’re all set!
zilchcarnon Please open a support ticket https://www.kemper-amps.com/contact
riotmetal79 Your Profiler does not show any annomalies as i have told you numerous times. It passed all tests.
Please do not mix completeley different issues.
I replied in the ticket. Please provide the info i asked for.
Sorry for the inconvenience.
I just plugged in my guitar straight into the Kabinet, turned up the volume all the way - and could easily talk to my family across two rooms. Does anybody have tried this and can share his/her experience with me. Thanks!
This appears to be normal as the input of the Power Kabinet needs to be driven by a Line Level Signal.
Please open a support ticket https://www.kemper-amps.com/contact
Thank you both for clarifying. I’m a home player so not using the Mains is not an issue for me.
As you do not use the Main Output for anything else you can keep the H9 in the loop and connect the BAM to MainOut.
Please be aware that the JDI engagaes a bandpass filter to emulate a 12" Speaker when activating the Speaker -30dB PAD.
This is not supporting the concept of a Direct Amp Profile, as it introduces a speaker emulation.