You could order your preferred Profiler Model from the Kemper Online Store. We offer a 30 days money, back no questions asked policy. this would give you enough time to try the Profiler thoroughly in your personal set up.
Posts by HELL-G
-
-
To clarify:
You need to send e.g. CC#51, value 1 to select Slot 2 of current Performance. Then send CC#51, Value 0 shortly after it to emulate a switch being depressed and released.
Then send CC#51 value 1 again, it will trigger the Morphed State of the Rig in Slot 2. Send CC#51 Value 0 again.
Send Value CC#51 Value 1, the Morph to Base State is triggered correctly. Send CC#51 Value 0 again
and so on.
Otherwise the MOMENTARY option in Morphing would not work.
-
Have you tried the groundlifts on your Profiler?
-
The Profiler will work as expected. The sensitivity does not change as far as i know.
The failsafe function of the power amp just cuts out for a short moment, then kicks back in.
I have tested this myself and before running into any critical condition you experience deafening volume.
We use a 8x10 4Ohm Cab in my rehearsal space and it works just fine both at low volume when rehearsing with additional in-ear monitoring and the cab just providing some 'body' to the overall sound as well as at high volume with a 5 piece metal band with a hard hitting drummer.
I personally would go with th 4 Ohm.
-
welcome to the forum.
From the Main Manual:
The internal power amp is mono and delivers 600 watts at 8 ohms; however, the wattage will be lowered to 300 watts when used at 16 ohms. The power amplifier provides sufficient headroom to avoid clipping, even with dynamic clean sounds. Very loud signals and transients will then be compressed by a nice, organic-sounding soft-clipping circuit. You should, however, use these 600 watts of power with caution - if you are running at high volumes and notice any indications of speaker distress, turn down Monitor Volume or Power Amp Boost. The parameter “Power Amp Boost” can be found on the last page of the Output Section, where you will also find a watt meter that shows you how many watts the power amp is using at any given moment.
At 4 ohms, the wattage is electronically limited to 600 watts. If these 600 watts are exceeded the power amp is deactivated for a short moment, which causes a short dropout. It would require insane volumes to experience such dropouts. However, if you are connecting a 4-ohm cabinet, you should test it carefully to ensure that your loudest signals stay below that critical level.
Does that help?
-
Does some condition have to be met for amps being selectable?...maybe some tag thats a requirement?
Make sure that view is set to „from Rigs“. Use the TYPE knob.
-
What exactly do you want to achieve?
-
Sure. Go to RIG Menu, page 3. choose Location for the Expression Pedal, check 'Lock Vol. Pedal' box.
-
Check your Output settings. Set to Master Stereo.
-
Love to get one but for 2 weeks all I see is:
Where are you located? I can navigate to the shop without problems.
-
He pulls some great tones out of his Kemper, that's for sure.The Profiler Alex used on that occasion was loaded with factory content only.
-
Hey, what's with the "split" SC's at 4:32, Alan?
I'm no guitar-hardware expert, but I haven't seen them before. A custom job for Glen?http://glguitars.com/product/comanche/
Find some info here. Hth.
-
1) Is there an online list of every rig/profile that comes stock in the Kemper (for the latest update)?
You find a list here:
-
(actually wanted the HR824 but those were out of my range all)
I own two sets of the mk I version. Bought the second set 2nd hand. They are very good, i love them with the Profiler.
-
Turn the TYPE Knob all to the left until you hit a blank.
-
Nice! The Valve cab did sound better, I just imported one of the Marshall profiles. They sound really good though.
Yeah i think Tommy uses one of the rigs with a Valve cab.
-
Although I did speak to Tommy Victor from Prong last year and he said he used BE100 profile from the Rig Exchange, but couldn't remember which one.
Check out the BE100 Rigs by author Dill, especially the ones with the Valve cab.
-
You should also check out the Shure E609 or E906. Those are supposed to be great for recording distorted guitars. I want one.
These are made by Sennheiser i think.
-
I'm having the same problem, but only when using 4CM and Mesa cab with the Poweramp output. DI to the house works fine. Any help would be appreciated.
What is your cabs impedance?
-
Die Neutrik XLR Stecker lassen sich in sieben Positionen montieren.
