Bit of a long one this.. but I thought I would share some of the testing I've done to try and get to the bottom of my v3 problems. I hope the devs don't mind me posting this here, I have also sent it to them via the support ticket.
I started off by installing V3.0.0.10856 using the USB boot method
I performed an init flash to clear out all existing rigs.
Once it was rebooted I connected the Kemper up to my PC and started
rigmanager
Test 1) Installed Merged Rig Pack
I unzipped the contents of the merged rig pack into a folder on my PC
then dragged and dropped them into "my profiler" in rig manager.
They transfered over fine and I could swap between rigs either via the
Kemper direct or by using rig manager
Test 2) manual transfer of Factory rig pack using Rig Manager
I unzipped the v3 factory rig pack onto my PC and started to copy them
over to "my profiler" folder within rig manager.
I selected the following rigs (I ordered the rigs in alphabetical order
and selected a few at a time):
1962-electo through to Bass Driver - All transfered ok
Broken Heart through to FP-sun three hundred T - Software
error occured
I rebooted the kemper and within rig manager I could see most of the
last batch had transfered but the block converter distortion to FP-Fan
BM 1959 were missing
Test 3) - copied the next rig FP-voice acethirty using rig manager and
the Kemper instantly threw up the following error:
expr=DABT PC A02B6004
file=unknown
line=0
swvs="release:3.0.0.10856"(CRC=D4f027D7)
Pressed exit to reboot
The Kemper reloaded ok and I could see that there were 75 rigs installed.
I then performed another init flash to clear out all the rigs and reset
the Kemper.
This time I tried only the factory rigs rather than starting with the
Merged Rig Pack
Using rig manager again, I started to move rigs over to the Kemper in
small blocks
1) Broken Heart to Convertor Crunch - OK
2) Convertor Distortion to Engle Powerfall Hi Sue - OK
3 ) Fat Ed to FP-voice ace thirty - OK
4) Gadda da vida to Hey Jim - OK
5) Highway-201502-13-57.39 to KM Thrash - Produced software error on Kemper
expr=DABT PC=A004F574
file=unknown
line=0
swvs="release:3.0.0.10856"(CRC=4B007270)
I pressed exit which caused the Kemper to freeze with a blank lit screen
I then rebooted, total number of rigs = 105
I checked to see what rigs were missing from step 5
(Highway-201502-13-57.39 to KM Thrash) and could see KM Arrival Clean
through to KM retrospecial were missing, however KM Sea Nymph to KM
Thrash were present.
I then tried to transfer 1 more rig - KM TOP Romulan, this caused the
Kemper to fail showing just the Green Screen with the Kemper Profiler
display
Rebooted and I could now see 106 rigs, including KM Top Romulan.
I then transfered 1 more rig - little pop prince, I didn't see it
transfer on the Kemper screen but no error occured.
I tried to select a rig using rig manager which caused the same fault..
Kemper froze with the Kemper Profiler display
I then rebooted Rig Manager and the Kemper
On restart the Kemper is showing 107 rigs and little pop prince is
installed.
I selected little pop prince in rig manager and the kemper loaded it ok,
sounded ok.
I then moved the next rig Little Prince MD421 over to the Kemper using
rig manager which caused the following software error:
expr=DABT PC=17CED8D8?
file=unknown
line=0
swvs="unavailable"(CRC=010D2D30)
I pressed exit and got the next error:
expr=DABT PC=A000DEAC
file=unknown
line=0
swvs="unavailable"(CRC=01002D30)
I pressed exit and got the following error
expr=DABT PC=9FDC0150
file=unknown
line=0
swvs="unavailable"(CRC=01002D30)
I pressed exit and got the following error
expr=(regindex>=)&&(regindexx<BOARD_NMBREGS)
file=../arn/board/board.c
line=120
func=boardGetRegByIndex
swvs="unavailable"(CRC=010D2D30)
I pressed exit and got the following error
expr=DABT PC=400048B0
file=unknown
line=0
swvs="unavailable"(CRC=010D2D30)
I pressed exit and the Kemper froze on a blank lit green screen
Rebooted the Kemper and it loaded OK with 108 rigs
Little Prince MD421 is in the kemper, I tried to load it but got the
following error
expr=DABT PC=A0000084
file=unknown
line=0
swvs="unavailable"(CRC=071B086F)
Pressed Exit and got another error
expr=DABT PC=A0000090
file=unknown
line=0
swvs="unavailable"(CRC=01002D30)
Pressed exit and the Kemper rebooted itself
I tried to select a different rig and I got the following error
expr=instance <mMultiplicity
file=
line=843
func=const int Access::logicEngine::Expression::GetLastResult(int)
swvs="unavailable"(CRC=A100F408)
Pressing exit just repeats the same error.
Powered off.... end of testing