Posts by scrubs

I am not sure if this is the same bug that has been mentioned before. I have a dedicated pitch pedal, as well as volume and wah. Along with a ring modulator sound mentioned by others, I can't seem to zero the toe position. It is around one semitone too deep. I tried to correct this in the System settings and both volume and Pitch keep reverting to 118 (a full toe down for the wah is 127).

OK, thanks. I'll try it!

I've worked it out by using PEDAL PITCH instead, which gives me options up or down with the toe!

Hi. I am planning on using the Dunlop DVP 3 for Pedal Shift, but want the pedal to pitch up to the note when I toe down. That is, opposite to the Whammy effect, which pitches down with the toe. There must be a setting I'm missing?

Got it! Thanks. There was still one old file I hadn't deleted!
Cheers

Hi all.
Not sure what I'm doing differently this update. I'm getting the message "Cannot Update. Multiple software revisions have been found on the USB stick", even tho' I deleted them.
Any thoughts??

OK, thanks.

Hi, I'm setting up my remote and want to use the Effects slots. My question is, are the stomps and effects you have to choose from limited to those already allocated in Stomps A to D and Effects X, MOD, Delay and Reverb (which add up to 8 choices) on the Profiler? In other words, the choices for the 4 Effects buttons on the remote are restricted to mixes of those 8 choices?
Thanks
Roger

Hi, I've just updated to the new OS and want to use pedal pitch and also morph other parameters at the same time with the same pedal2330.
Is that possible? Thanks in advance.
Roger

This is our rehearsal room, I'm using the Kemper through both the Atomic CLR and MarkBass amp. I find it adds volume and depth to the sound. And great when I switch to using bass with the bass profiles. Very light to move to load up the vehicle. They're all neo speakers.

Thanks for the replies! Used the 'lock' method. And the stomps and effects matched in all performances, which is great. However, not sure about how to 'unlock'.
I pressed the 'lock' button to do this and all the configured stomps reverted to previous settings!

Sorry if this has been covered already. I want to keep the same stomps and effects for every performance, so as to keep my options easy to remember when using the remote. Much like a pedal board. Is there a quick way to store the settings without manually copying and pasting individually 125 x 5 times?
Many thanks
Roger

Thanks for the replies. I deleted around 60 profiles from the Kemper in order to make room (and saved copies to my hard drive).
Have the new purchased profiles (unzipped) on the USB stick (where they were when I started my first attempt at import) , but cannot seem to get the remaining 45 to import to the Kemper.
I'm not sure where I'm going wrong!

Also, the Kemper states that there are no rigs to import (but they are present on the stick).

Hi. Looking for some help.
I purchased and downloaded 60 profiles and then transferred them to the USB stick, but can only seem to transfer 15 of the profiles whilst importing to the Kemper. I've repeated the importing process a few times. Is there a limit on how many you can import? I have 999 profiles in Browser mode.

Thanks. Really helpful. I have locked in some effects using 'lock' to be present in all the rigs, so as to be consistent and easier to remember when using the controller.

Thank you for the reply. You noticed my first post! Makes good sense that the wah needs to be allocated a specific position in the signal chain.

I want to be able to have the left hand pedal on the FCB set to wah on all performances (in Perform mode) without using up a Stomp slot. I want to keep the Stomps for other options. How does one program to do this? I can program one rig at a time on Browser mode by using up one stomp slot. But can the wah be always on and available without taking up a stomp slot in Perform mode? In other words, do you need to allocate the wah to a Stomp slot to work?