do you use performance mode?
Posts by Awesome_Elvis
-
-
what about an expression pedal? You could assign a morph.
-
not sure if this will help but since you're close ,you could try to add a studio eq after the CAB to give it some extra , niceness! Lol
Chairs! -
Heyy! Try switching the cabinet portion to a cabinet from a different profile, this will change the sound drastically and can get you closer to what you have in mind.
Select the CAB module by holding it down and then you the browse knob to scroll through different cab profiles. A soft button above the screen is assigned to select either "presets" or "from rigs". Once you find a cab you like or close, you can then tweak it with high and low shift etc. if needed or wanted. You can then save that cab as a preset and recall it whenever you like! You can also name it something like A cab, B cab, C Cab, Cab1, AA Cab etc.
-
I want a t-shirt that's says Reverb in kemper font.
-
catalinbread Topanga spring reverb I think
-
sometimes I feel like I need this 2x12 mission passive cab AND a stereo frfr. Thinking about the headrush frfr which is pretty much the same as the alto but whatevs. Powered toaster into passive 2x12 and then quarter inch main outs to 2 powered frfr. I have a synth rig that I could run into them as swell. 0.o
-
-
cabs do get a bit boring after a while. I'd also choose frfr but have a cab too for when you just miss it lol
Live, I also like both at the same time but would choose an frfr backline over a cab but then again, depends on what's going on with the rest of the band and the venue I'm playing in. Music genre is arguable
-
Love the title of this thread!
Welcome!
I propose a toast (lol) , to our new companion!
Chairs!
-
I'm not seeing Formant Shift or Detune in the Pedal Pitch parameters. I can get a more garbled sound by pressing the Freeze Formants soft button but that makes the whammy largely useless for the other parts of the song, although I might save this sound as an extra rig in my performance.
if they aren't on a different page then I would just use the chromatic pitch and use the morph feature to change whatever parameters you need to change? If you only need 1 pitch shift, you can just leave the other one set unison
-
I just listened to that song for the first time in years and wasn't sure which one it was till the chorus kicked in! Lol
Anyways, I would say try messing with the format shift and the detune on the pedal pitch or chromatic. Try them in small intervals and resort to extreme values later if necessary.
I've noticed to get a good replica pitch shift like a pog or whammy you gotta add some of that "zizzle" in there. Hope this helps! Cheers.
-
-
-
thanks dude! I had a feeling that was probably the best formula but it's good to have someone else say that!
On a side note, how do you feel about monitor cab off vs. Cab off? I haven't been running direct but I like to set it up for that but I feel there is a difference between the two.
-
if the master volume us post effects loop, what are the balanced ratios for kpa "whatever output you choose master volume" to the master volume in the amp? And before anyone says use your ears, that's not what I'm talking about. I've already done this before and could never figure out if i should dime the amp MV, or should I dime the kpa and slowly raise the amp MV. I also tried setting them both somewhere in the middle but then which one do I raise first if I need to be louder? I found myself raising both without a real sense of what i was doing was best/ideal. Chairs.
-
I make sure to turn the definition parameter down below 5.0 on any profile I use. It's amazing how many profiles I've downloaded that have it set on 10.0 which sounds terrible (no low end and cocked wah sounding). Turning it below 5.0 brings the low end thickness back.
Never thought of this, I'm gonna give this a try!
On the down side though it would effect the front of the house sound. -
-
I haven't tried a harmonizer in a long time and I wasn't that good with it to begin with but since then I have an increase in mode and scale knowledge.
So for harmonizing leads, where do yall recommend putting this effect? Front, back, post, pre? lol
-
《Michael Jackson eating popcorn》
Would anyone like some Sour Patch Kids?
I originally bought the Kemper because it could profile an axe fx. LMAO
So what does that really say?
The Kemper is Morgan Freeman talking to me a couple feet away but he's holding a small thin napkin in front of his Face. I know it's him.
That's what this is. The axe isn't much different but it is different sometimes?
Some days, I prefer a couple pedals stacked, running them into the effects return or power amp in of any amp. I made a profile with amp turned off for cleans cab on and dist stomps for the dirtdirt with cab on, did the same on my helix with and without multiple stacked IR's and loved it so I profiled that too. Try it , I dare you, any of you. I'll do the same with an Axe III. Or even better. There's a chance for new tones and yall wanna cry ,moan, or slap fight each other like a bunch of sophisticated internet sissy Sonic The Tonehog man babies. Lol
It's funny though. I don't really know why I keep reading this thread. I sometimes skip around because I get bored but lucky me, yall keep quoting each other so I don't miss a thing. Not that I would miss anything if you all didn't quote each other. I also keep waiting to read something useful HAHA jus playin, sorta
Just for fun i would like to test my might at the audio samples. I have no horse in the race and could care less of the outcome. I also have never owned an axe fx or played one but have heard them here and there. Chairs kitties!