Maybe holding down the Looper button on the remote for 5 seconds could toggle it.
When you play with looper live and want to switch to pre or post - 5 second is a lot of time:)
Maybe holding down the Looper button on the remote for 5 seconds could toggle it.
When you play with looper live and want to switch to pre or post - 5 second is a lot of time:)
Could you post a sound clip with direct from KPA and direct from your amp?
BTW. I don't believe that EL34 is the case:)
RJ45 in KPA has one advantage- if someone pull the cable its a chance that KPA will not hit the floor:)
Thanks for this info Damian.... although I am pretty much useless when it comes to building/soldering/creating anything like this. I am destined to fork out more money and just buy the palmer box instead of being able to make one on the cheap. I look at your diagram and I can't work anything out lol. Thanks for your input though
No problem:) Palmer is good company - PCABM is quite cheap:)
you can buy 3 x mono jack input and connect them like in the picture (connect green connections all together and connect reed connections all together) and buy three speaker cables and small box for splitter:) it will cost you 5$ Or buy a palmer PCABM.
[Blocked Image: http://gaussmarkov.net/images/plugs3.bmp]
What about profile the KPA with another KPA ? You would need password protect your KPA boot Just kidding
connect them in serial or parallel - what impedance of output has your KPA?
If you want to connect in parallel you have to switch to mono and connect Y cable to 16 Ohm inputs . This will give you 8 Ohm Impedance of two cabs.
Unfortunately Mr Kemper, I am completely color blind. I can see the little lights but I can't tell what color they are. I did check my input sensitivities and they were at the original settings.
Maybe you can ask some person to help you with clip indicator or record it with telephone and put in here.
The simplest solution for this is to add another selection in profiling mode(after clean /distortion) Di profile/studio profile , so profiler will be forced to use selected mode.
The Mustang Floor also has midi so you could use it as a foot controller for the kemper.
Yeas - but the Midi CC in mustang floor are hardcoded and unchangeable:(
Thnx for the replies.
I've read somewhere that thats the way it was supposed to be. Mono out and stereo return sounds logical. Maybe one day we can choose 2 rigs or two cabs/mics and use the monitor out as a real stereo fx loop
anybody an idea on the ducking? I Can't seem to turn the ducking off. Could this be a bug? In that case, should I report it somewhere?
If you take your output from main output make sure you have set Main Output to Master Stereo in Output settings (not Delay/Reverb wet) - maybe this is your Issue.
After cab there is only a mono signal so you cannot send stereo - Loop stereo has only stereo return.
I think the Git+ processing - it sends clean guitar on one chanell. Try with Stack settings on direct out.
You can only send Mono - and return with stereo( return + alternative input).
So use only one input on your external gear or buy a Y cable.
I have a Mustang Floor and if you do not use pitch shifters or high gain sounds it is good backup:)
What about Looper switch(near the tuner switch) - it is disabling the looping sound - or just switch the functions of other switches?
With midi implementation it would be possible
The SysEx messages at the first post in this thread aren't NRPN.
Are they disabled as well?
These are no SysEx messages- SysEx starting with $f0.
They are pure NRPN but in one "packet" of data.
I'm wondering if what has been blocked is NRPN access or the entire looper capabilities via the MIDI input.
We don't know - because if you can't record anything - you cant test the rest of the functions.
Great video Sean I like this space -freeze sound
I've pasted video in the OP - if you don't mind.
This is nice example that sometimes you have to use custom - defined MIDI pedal board to achieve more complicated stuff.
And thats why the NRPN (and CC) messages(not only the looper ones) should stay in next KPA FW's.
It's no BUG. You have to connect Remote - beacouse this page is simply inactive without remote. That's why it looks like that:)