Ja, dann noch auf Lock setzen, dann geht sie auch nicht mehr an.
Posts by MtotheEikel
-
-
Gibt es einen Trick wie man den Slot für Delay auch für anderes hernehmen kann, zB für EQ? Bei mir kann ich den Delay Slot nur für verschiedenste Delay-Arten hernehmen
Ja, wie Sharry schon sagte: Mach mal ein Update. Dann hast du auch ganz viele neue Delays und weitere Verbesserungen, je nachdem, welche Firmware du momentan nutzt.
-
Ja, das stört mich auch. Output Presets nutze ich nicht, aber bei Input Presets gibt es genau das gleiche Problem.
-
@MtotheEikel
Möglicherweise habe ich @mysterious falsch verstanden, aber ich glaube er redet insgesamt vom Highgain-Bereich und eher nicht von clean.Du hast Recht. Den Abschnitt, in dem es um High-Gain Sounds geht habe ich wohl übersehen.. Sorry, meine Anmerkungen sind in dem Fall wohl nicht hilfreich.
-
Hm, ne eigentlich nicht. Clean Sense ist für das Verhältnis der Lautheit zwischen cleanen und verzerrten Profilen zuständig und sorgt dafür, dass rein cleane Profile auch wirklich clean sind.
Ich weiß schon wofür man die benutzt. Aber im Prinzip ist das doch nichts anderes als eine Eingangsverstärkung, aufgeteilt nach Gain-Bereich, oder?
Das ist doch wie am echten Amp: Im clean Kanal sind outputstarke Gitarren lauter als solche mit wenig Output. Was man dagegen tun kann ist, den Gain Regler zurückzudrehen, also weniger Verstärkung am Eingang einzustellen.
Beim Kemper wird diese Funktion von clean sense übernommen.An der Stelle von mysterious würde ich das einfach mal probieren und mal überprüfen, ob das Problem nur bei clean sounds oder bei allen Sounds auftritt.
Aber so lange mysterious im Urlaub ist, können wir sowieso nur im Dunkeln stochern. -
Den Delay Slot kann man für alles nutzen. Reverb leider (noch?) nicht.
-
Tritt das Problem auch bei verzerrten Sounds auf? Eigentlich machen die Sense Regler das, was du suchst, nur eben aufgeteilt je nach Gain.
-
gefühlt hätte ich da gerne die möglichkeit, den input etwas zurückzuregeln - finde dazu aber spontan keine möglichkeit
Clean Sense im input Menü.
-
Mit "Hold" kannst du auch arbeiten. Das ist eine Checkbox in den Delay Settings, die sich auch auf Fußschalter legen lässt.
-
I use different input settings for different guitars. Imho this is an easy but very useful feature.
-
This feature is called morphing. Look for morphing in the manual or search the forum.
-
The good thing is, that ypu can also adjust EQ changes for your solo tone if you like.
Very easy to set up and use. -
Do you mean: Locking an EQ pre stack, dial in certain EQ presets for each guitar and and then call them up when you change guitars?
Exactly.
-
True. But if you already think of one there's a chance you'll think of the second too. Another solution is to put an EQ pre stack on every rig. But this will raise the amount of rigs/performances.
It could be locked and switched with the guitar. This wouldn't increase the amount of presets but you only have 3 stomp slots left.
If this is enough, you're good. -
Hold the "Lock" Button and choose either the slot "A", "B", ... or the whole "Stops" and / or "Effects"-Section.
... or hit the lock button while you have selected a stomp. Works both ways.
To answer your first question: Hit store.
... and read the manual.
-
Haven't you tried hooking up your speakers or headphones directly to the KPA to find the problem?
Anyway: Good to hear that it works fine now! -
Mono switch will come!
Great, thanks!
-
Just like any other fx preset. Try it, you can work it out.
-
No. He saved block C, not the whole profile.
-
You can find it by turning the browse knob while having any stomp or fx slot in focus.