Hi All,
Just updated and wanted to record by using the new USB feature.
I am experiencing a lot of latency - recording into Logic - Buffer size 64
Any tricks?
Hi All,
Just updated and wanted to record by using the new USB feature.
I am experiencing a lot of latency - recording into Logic - Buffer size 64
Any tricks?
I made a floorboard made op HPL (high pressure laminate) , I unscrewed the rubber feet and put longer screws thru that plate and kept the rubber feet in between the HPL plate and the stage
Raf
That was what I was thinking of as well
Hi all
How do you fasten your Stage to your board? I have mine in a flighcase and use some stron velcro - but when backline people pack my gear, it's not enough and gets loose.
Have you succeeded in mounting it with small srews underneath ? or something else?
Hi all,
Looking to get the above mentioned tone ..... The YouTube video from Tone Junkie is no where near (to my ears).
Do you know of a trick to get the DMM sound ?
Here's my version Still waiting for a chassis mounted USB connector from Neutrik. When that arrives it will be done.
I did this (waiting for a chassis mounted USB connector to arrive - It should arrive in less than a week) :
Matrix Q12a
Works perfectly - Very good condition - I will blow away the stage dust before shipping
250,- €
Located in Denmark - Will ship world wide
Hi all,
I have made a panel in the back of my rack for all connections going in and out of my Kemper and i wanted a spare cable. So I hooked up with one of my mates who works with installation of IT systems for large companies.
We tried a "normal" 10m LAN-cable .... the remote powered up, but couldn´t connect to the Kemper.
Then we tried a 23AWG 15m cable - BOOM, shorter startup time and locks in perfectly. Have rehearsed with it for 4 hours once and there are two more rehearsals coming up before the next show - If I don't experience any glitches I'm gonna make it my number one cable and then keep the original as a spare.
Hi all,
just updated to FW 5.0
I was hoping that i could choose a second Delay instead of the reverb in slot nr. 4 after the stack section
Basically I would like to have a Dual Tap (running a sort of Lexicon Circular Delay) AND a single tap (doing 1/4 notes) going at the same time - is that possible ?
Hi All,
I Haven't upgraded to the new delays - I-m a gigging player so I need to have stable set up. So I'll wait until the official release comes.
Have any of you had succes in creating a "Circular Delay" preset ? I REAAAAAAALLY miss my PCM70
Hi All,
Just did the update to 4.06 (used 3.3 before ).
Now when i play in Performance Mode Slot 1 and i turn on some effects manually - Then switch to slot 2, everything is fine - But when i switch BACK to slot 1 the effects are still on ..... Where do I turn that off ?
I want it to load the rig i stored in Slot 1 and nothing more
Hi all,
When performing I use only 2 performances. They have the same combination og rigs in slot 1 to 5. Performance 1 has dry rigs, performance 2 have the same rigs, but with all the effects on.
My question is : When i have to edit one of my effects I want to make it "global" for both performance 1 and 2. Untill now I have edited the same effect in each rig in the performances - But, can I edit it only in one rig and then make the chances count in all my performances ?
Hmmmmm ..... maybe I could do that. I want to be able to turn my boost on/off when ever I feel the need and on any given preset.
I have my foot controller (All Access) set up, sop that I have 5 presets in each bank and 10 on/off switches for alle my effects and tap and so on.
That's not working well depending on what settings you have. The amp itself produces frequencies over 10.000 Hz even if you cut them out before the amp.
Give it a try. Use i. E. a EQ before the amp and cut everything above 10 kHz then add a tube screamer and dial some gain for the screamer and the amp in. Then place an EQ behind the amp and use your headphones while cutting out everything above 10 kHz and you will notice that there are in fact again frequencies over 10 kHz.
i know - which is why I would like i in the AMP section - and as statede earlier - I need the 4 slots for effects Or..... I will have to use chorus in mono ....yikes !
Bugger ..... I need all 4 slots after amp section for Lead boost, Chorus, Delay and Reverb
Must try with an EQ before amp section
Hi All,
I would reeeeeeally like a high/low cut option in the "amp" section - I know it has come up in "future request" - but have they incorporated it in 4.0 ?
I cant upgrade to 4 because I'm a gigging musician and need my Kemper to run flawless every day.