Posts by thisamplifierisloud

digbob It's yours !

@G String Of course, you're right.

For higher distances a PoE Injector is required.

I will leave the original cable plug untouched for spare,

so it fits into both sockets.

My Cordial cable is now 2-sided ethercon.

If someone is interested, the silver one is leftover.

A small donation is welcome.

If more is required, I can arrange a small batch of plates or complete sets.

PS Works fine with the original cable, too.

THX !

Maybe 0.5 seconds would be enough.

These old eyes ... the dark sunglasses in the night ... and my feet as big as child´s coffin ...

Yehaaa !

Works fine with

- cheap & old CAT5e cable (5,5 meters AWG26)

- 5m Cordial CSE5NH5

I made a new plate of anodized aluminium with nice engraving of a longhorn

and my name/address (Maybe this helps in case of loosing my toaster).

Twang !

Here´s my approach to the Toaster´s RJ45 socket weakness.

A CNC milled 2mm aluminium plate, a Neutrik Ethercon socket and a short angled network patch cable.

It fits exactly and is mounted using the original screws.

I will carefully test this with the original remote cable and my spare remote cable (5m Cordial CSE5NH5).

If there are no problems I will modify my cables into a 2-sided ethercon cables.

Stay tuned !

Best regards

Bernhard

+46546765 !

Why only 2 .... should be 11 and you'll get a boosted starfighter's engine.

Sorry, but I HAD to snapshot this sticked at the fridge of our rehearsal room.

Den RM mit admin Rechten neu installieren ?

Yes indeed, also I am missing a parameter for effect´s volume.

In addition, what about adding HighCut and LowCut to each rig ?

I see at the rig menu of each rig things like Transpose and so on.

Would be a wonderful place for the cuts.

A high gain rig needs a lower HiighCut frequency as a Clean or an acoustic rig.

Why delay / reverb mix only ?

Wouldn't it be nice to assign every parameter to an expression pedal ?

Per rig, not global.

(Not everything may have sense)

Hod Rod Deville 3 by C.Kemper

Very nice dancing on the edge of breakup with my telecaster.

Without any effects except a reverb.

I found the solution buried deep in the manual at the dalay's description !

(May there should be a hint about the influence to spillover)

I changed the delay's mix: post to mix:pre

Now it's spilling over and over and over and over and over

and I am soooo happy ! Yehaaaa !

@Helge thanks for your fast response.

The ticket can be closed.

May I get an email, too, please ?

[email protected]

gmoo ... means Gary Moore

But to be respectful : my fingers aren´t as fast they should be.

Best regards

Bernhard

Thanks for your answer !

I didn't hear a spillover because I usually use morph for solo sounds.

I raise the gain and the delay's feedback and mix. (works great btw !)

I figured out that after activating morph spillover is missing at changing the rig.

Change the rig without morphing : spillover ok.

Raising delay's feedback and mix manually then change the rig : spillover ok, too.

Is it a bug ? Shall I open a ticket ?

Grüße aus dem Schwabenländle

Bernhard

ckemper ?

Burkhard ?

In the manual I cannot find any limitations due to morphing,

so I don´t know, is it a bug or is it intended behaviour.

The only restriction I found : delay at the delay slot, reverb at the reverb slot.

This I´ve done correctly.

I hope one of the kemper specialists knows more about it.

I was missing spillover since approx. 1254 years...

Delay is located at the delay slot, reverb at the reverb slot.

In Rig menu page 1 the checkbox for "Rig spillover Off" is off.

But I never heard a nice spillover...

Why ? Now I figured out :

I am usually incrementing rig´s volume and delay feedback/mix a little by morphing in order to get a nice solo sound (works great!)

Morphing is engaged by re-pressing the same footcontroller´s button.

Changing the rig from a unmorphed sound => spill-over

Changing the rig from a morphed sound => NO spill-over

Am I doing someting wrong ?

Is there a trick hidden in the manual (I read, but found none)

(I am always using the browser mode, for me it feels more simple)

EDIT : Actual software is OS 7.5.3.18561B,

but as mentioned above, I never heard a nice spill-over before

Best regards

Bernhard