Vedi la risposta sull'altro post.
Posts by Andrea L
-
-
No, non è possibile.
La chitarra non ha nessun ruolo nella profilazione se non quello di regolare correttamente l'amplificatore e rifinire il suono al termine.
La profilazione vera e propria viene fatta direttamente dal Kemper col suo set di suoni.
-
Yes.
You can select "WahPedal>Volume" function.
If you have a wah effect active, the pedal control this effect, when you switched off wah, the pedal controls volume
-
No, positions of effects are fixed.
-
Thanks guys! But let me put this on a clear picture. I don't want to use kemper for it's preamp but just steal the imprints that i can use with my full tube amp (preamp + power amp ). I have a JCM 800 and 4x12 kone cabinet and i just want to use the imprints from KPA somehow, of course it will be coloration from my JCM 800 and that's intended since i'm not using KPA preamp or rigs. and all i want to use the Imprints technology to get the Imprints Does it make sense ?
Guitar > JCM800 AMP > X ? > 4x12 Kone Cabine
There is a problem when you use the Kone with a full tube amp.
What sound do you send to FOH?
The Kone It isn't engineered to be miked.
-
L'assegnazione delle funzioni dei pedali è globale.
Però con le funzioni logiche "WahPedal>Volume" e "WahPedal>Pitch" puoi utilizzare un unico pedale come volume, come wah o come Pitch a seconda dei settaggi di ogni singolo rig.
-
I'd like to see the OS-Version-number coded in the kaos-filename.
I'm in Need to drive different OS-versions in my two Profilers, because one of them is linked to a Win7-computer, so I can't run the current OS-Versions.
for update-reasons I normally use USB-sticks because one profiler is in our rehearsal-room the other at home. After a while (of confusion) I cannot see which OS-Version is on which USB-Stick.
An indication in the OS-filename would help much !!
+1
-
The thing i keep seeing here is that the Kabinet is to be connected to the monitor output, but as a cab shouldn't this primarily be the speaker output (i.e. like a normal cab)? Surely the Kone IRs can be used on speaker output mode too for all profile types.
Lots of conflicting information and nothing concrete to say it can be used in that way when also recording through S/PDIF etc. also.
Speaker output have the same features of Monitor output, without power amplifier.
For connect the Kabinet with Monitor output you need an external poweramp.
-
Thomann controller is rebranded Meloaudio MA1010 controller.
You can download manual here
-
Set the pedal as Wah and select "WahPedal>Volume" function in System Settings.
You can find detailed information on page 126 of the Main Manual 7.0
-
You can adjust the height of the switch through the two nuts that lock it.
To raise the switch, remove the back plate, release the internal nut and then lock the external one.
To lower the switch release the external and lock the internal
-
You can adjust the height of the switch through the two nuts that lock it.
To raise the switch, remove the back plate, release the internal nut and then lock the external one.
-
It's a normal behavior.
From Main Manual:
"You might notice that your
reference amp is not muted when you listen to the internal PROFILE - this is intentional, as the acoustic signal of
your reference amp will always mix with the sound of your studio monitors, even if you have it in a separate room.
While this may influence your perception of the sound through the studio monitors, it shouldn’t affect the A/B
comparison. However, if your reference amp was muted every time you switched back to the PROFILE, a valid A/B
comparison would be impossible."
-
Are the MIDI PC numbers
-
I have the same problem with firmware 5.7.7
-
You can find the same controller (rebranded as Harley Benton) on Thomann.
-
I’ve been using Klotz La Grange for a few years now and they’ve been very good IMO.
I use the same cable. Have a good tone, low handling noise and is very reliable.
-
A live vid from Marco Fenton (kemper profiler). The demoed says the software is version 6.0 ar 2:40 or so
Can any of our community that speak Italian translate what Marco is saying at the end of the vid?
At the end of the vid Marco say that is possible to set a cab simulation with a serie of parameters dedicated at the cab type.
-
Hi,
did you see the knobs?
They have a different scale lines… does it means that this is a new model or it is just a graphic change?
Hi Allex,
my kpa (November 2017) have the same scale lines. It also has two other aesthetic differences compared to older version:
PROFILER instead of PROFILING AMPLIFIER and RIG VOLUME instead VOLUME.
See you under the Neptune
-
I bought mine in 2015 (ordered in March), Andrea, and my unpowered rack already said, "Profiling Amplifier", so it must've been more than two years a go; mine's almost 4 years old.
I'm sorry Monkey_Man.
I did not explain well.
Newest KPA (head and rack) are labelled only
PROFILER.
I bought my unpowered head in 2017 (November) and it is labeled only PROFILER.