Die Aux In Funktion ist dazu gedacht, um ein externes Audio Signal zu seinem Profiler Signal zuzumischen.
Ein versuch ist es wert, acht einfach darauf, das der Pegel, der aus dem Kopfhörerverstärker kommt nicht zu hoch ist.
Das Output Menu page 6 bietet dir ja die Möglichkeit dieses Signal dann dem jeweiligen Ausgang (in deinem Fall der Headphoneausgang) zuzumischen.
sounds like a wrong routing in the apollo software and / or the DAW, you get a feedback into the Profiler.
For reamping a sound make sure to chose Master Mono / Stereo to get the sound of the complete signal chain.
Git Studio offers you to record a Di signal of your guitar.
Which output of the Profiler do you use to get the signal back to your apollo?
Have you already checked the output settings in the output menu?
Maybe you have assigned a di signal like the setting "Git Studio" to the corresponding output.?
Is it possible, that the locking function has nothing to do with it?
If I implement a Rig via Browse Knob in a Slot in Performance Mode, then exactly this Rig also appears in Browser Mode when I switch back to it.
The deciding factor is, I have to select a rig via the browse knob.
Can you confirm that?
is it a new Profiler or a second hand device?
Try to reset the global settings, system menu, page 1, soft button 2, init globals
Hi Aaron I tried to contact you via mail.
Our developer asks me which AMP you tried to profile
Unfortunately, I don't recognize the amp on your video correctly.
As I read, you were able to profile another amplifier over this setup without any problems and you suspect the amplifier itself is not suitable for profiling, right?
In the Kemper Merged Profilers Pack we have the EVH 5150 III Merged Rigs from all three channels.
Michael Britt was able to make direct profiles of the AMP.
From a distance it is really difficult to judge why you don't get exact images.
First, I would recommend you try the Profiler DI Box. Maybe you can get that from someone else for a test?
Another quick workaround..
Lock the effects on your Profiler after they have been assigned to the Remote.
The assignment is now retained on the Remote.
Go through each Rig once and save it.
Now each Rig has the same effect settings.
I would recommend that you upgrade your profiler to the new operating system version and then check if your problem is solved.
I recommend you to send in your unit to the Kemper Service Center. (contact support)
The warranty would expire if you repair the device yourself. (If it is still under warranty)
I also want to warn you about consequential damages, if something goes wrong during the repair and you install the wrong component or something similar.
Only the best for your Profiler and in the repair center the specialists know exactly what to replace.
It isn't necessary to use a DI Box.
Go straight into the stage box via XLR
Die Remote Control behält ihre Funktionen bei.
Du kannst also über die Remote (1-5) die Rigs ansteuern sowie über den externen Fußtaster.
Du kannst den Profiler Switch 2 Way im System menu so konfigurieren, dass der Tip als Rig Down und der Switch als Rig Up fungiert. Somit kannst du die einzelnen Rigs hoch oder runter schalten. Man springt auch in die nächste Performance wenn man beispielsweise von Rig 5 einen Slot weiter hoch spring sowie umgekehrt auch in die vorherige Performance.
Das ganze dürfte aber mit jedem Doppeltaster funktionieren, der als (Momentary) konfiguriert werden kann.
Is it possible that you can still hear the original tone of your guitar, which irritates you?
To rule this out, you'll have to make the signal pretty loud.
Our ears are quite impressive and can still hear the original signal of the guitar through headphones.
Record the transposed signal to see if it really contains another tone.
In the Output menu you are allowed to adjust the volume for
Main Out, Monitor Out, Direct Out and SPDIF Out separately.
The Monitor Output is internal linked to the built in power amp, so you are able to use the Monitor Output Volume Knob to adjust the level for the passive speaker.
From the manual...
The MONITOR OUTPUT is specifically designed to deliver a signal to your onstage monitors, assuming it is notalready being “abused” for other purposes as described in the chapter Output Sources.
The most common purpose of the built-in power amp of PowerHead and PowerRack is to drive a guitar speaker- cabinet, therefore it is cabled internally to the MONITOR OUTPUT. However, the MONITOR OUTPUT jack carries the exact same signal in parallel, so you can still use the MONITOR OUTPUT as if the power amp wasn't there.
Even with Profiler variants that don't feature the built-in amp, you can still connect the MONITOR OUTPUT to a full range speaker, or a powered side-wedge on stage. Remember, if the speaker has no power amp of its own, you will need to get one in order to drive it.
The MONITOR OUTPUT features an independent volume control, as well as a dedicated equalizer in the Output Settings. These allow you to tailor the sound to your speaker cabinet, while the other outputs remain unaffected.
Select a Rig from My Profiler, press Shift + F.
Press the right mouse button and select Make Favorite.
In your Favorites list in the Profiler, the Rigs should appear immediately after you have connected your Profiler with your computer via USB.
You can only save Rigs as Favorites, which are also available on your Profiler.
If this message has only appeared once, you can ignore it.
In your case, the message was generated because there was a problem synchronizing the internal clock of the Profiler with the clock on your computer while the Profiler was connected to the computer via USB.
Output menu page 2 --> soft-button 1 (Main out link)
You are able to link and unlink the different outputs to master volume in this menu.
System menu Page 1 --> Soft-button 1 (Edit Owner)
To set it up from ground level, you could reset the global settings.
Press the System Button while you turn on the Profiler into tuner mode.
Press andhHold the button till the message initializing global settings appears in the display, then let go of the button.
All global settings are now set to the default state, you have to set up the date, time and your name.
- The MONITOR OUTPUT allows to run the amp sound without virtual cabinet, while other outputs still contain the virtual cabinet. Engage “Monitor Cab Off” to switch off the cabinet in the output menu.
You will find a RIG Reference List on the website.
Profiler --> Rig Reference List