Posts by christianbad

  • Messed up sound with Formant Shift?

    i just tried the video settings, same weird sound. probably wrong settings shown in the video.

    never used the formant shift before, wasn´t able to get any useful sound with it.

    the manual describes':

    Since the Wah Formant Shifter is based on a pitch shifter algorithm, you will also find the parameter “Pitch Shift”. This gives you the option to shift the fundamental frequency up or down in semitones. At the lowest pitch, or longest delay, it will resonate on an E major chord.

    didn´t happen when i tried it. :/

  • Kemper USB record/play - a less limited solution

    Michael_dk regarding latency


    there´s a detailed examination about this here:

    Thread
    extra latency using SPDIF
    Hi

    I have just got a (used) Kemper and I am happy with it !
    I have a question about recording from SPDIF versus analog output.

    I have simultaneously recorded the same signal ('Master stereo') from both outputs (SPDIF Out and Main Out) with the same USB audio interface (NI Komplete Audio 6). The track recorded from the SPDIF output is 3.5ms later than the track recorded from the analog output. Do you know where this extra latency comes from? the Kemper? my recording system? Do you experience the…
    Emmanuel

  • Help with workflow when using the Editor

    why so complicated? please read again what i posted from the manual (#4).


    without Rig Manager:

    use the navigation cross to switch between slots ( modificatians remain) or undo your tweaks with the remote (= load saved rig).


    with Rig Manager connected:

    all tweaks are maintained, doesn´t matter if you change slots with remote or on the unit.

  • Help with workflow when using the Editor

    main manual p.296


    While navigating Slots within a Performance via the <PAGE> buttons of the PROFILER Stage, or the left and right RIG navigation cross buttons of the other PROFILER variants, any modifications (e.g. loading another Rig, or cranking up Gain) are interpreted as editing, and will be retained until you move to another Performance. Don’t forget to store before you load another Performance, if you want to make those modifications permanent.


    ✓As soon as you load another Slot from your foot controller, or foot buttons of the PROFILER Remote or Stage, any former modifications within that Performance are interpreted as temporary tweaks during a live performance and will be discarded immediately. If, for example, you had activated a booster in module B, or increased Delay Mix via pedal, any such changes will be lost if you switch Slots remotely. This way, you can always be sure that Slots will be loaded in their original, predictable state during live performances.


    ✓However, there is an exception to this practice: While Rig Manager is connected, any modifications are interpreted as editing and maintained during Slot changes as long as you stay within the same Performance.

  • Choose Source for Headphones!

    that´s already possible (manual p.128)


    Auxiliary Input

    The Auxiliary Input function allows you to feed a stereo signal, such as an mp3-player, into your PROFILER to play along with it. In the Output Section, the Auxiliary Input function is equipped with three mix controls: one to feed the aux signal to the MAIN OUTPUT as well as S/PDIF OUTPUT, and two others to feed it to the MONITOR OUTPUT and HEADPHONE output. This allows you, for instance, to add an additional monitor signal to your HEADPHONE output, while the MAIN OUTPUT stays unaffected.

  • Dedicated Reverse Delay

    from main manual, p. 238:


    You will not find a dedicated reverse delay, tape delay or ducking delay, as we realized there is no sense in splitting such crucial features into separate delay types. Instead, we have equipped every single delay type with most of these features. Why not have a dual reverse delay? Or a serial delay with analog tape character? Or a melody delay with ducking? All these are possible with the delays in the PROFILER.


    p.243:

    Reverse Mix
    When set fully to the right, the delay is turned into a reverse delay. With intermediate values, you will get a mixture of

    the forward and reverse delay, which is quite unique.

  • Hitzeschutz

    Ne Warnung gibt es nicht, der Profiler hat ja kein Thermometer. Bei extremem Wetter vielleicht ne Wetterstation dranschrauben ;)

    Das Handbuch sagt:


    Environmental Requirements

    Operating temperature: 5° to 45° C (41° to 113° F)

    Non-operating temperature: −20° to 47° C (−4° to 116° F)

    Relative humidity: 5% to 95% non-condensing
    Maximum altitude: 3000 m (10,000 feet)

  • Setup Stupidity

    i feel you, been there twice...really a bad feeling when you discover you plugged again into headphones. should be written in big glowing letters on top of the toaster: plug into the right input.