Could it be that half the world is at half speed due to Covid-19 and it´s mutant offsprings ......... 
2 years of lockdown, people sick staying home and over 5,6 mn people dead can have a negative
impact on production lines ........ 
Just a thought .....
Got me thinking of kasseler ....... 
Cheers !
Is it a volume pedal or a expression pedal ? TS or TRS cable ?
Cheers !
Hi !
Try to put the "Studio EQ" in X-slot and then turn "High Freq." down
to around 6 kHz and then the "High Gain" down to around 5 or so.
Different settings for different rigs
Cheers !
A new Kemper will stir up the market like they did when it first came out for sure.
It will have an AI based processor and dsp and will answer to the name Cheryl.
Voice activated program changes from a wireless neck mic and a deep learning AI that learns your playingstyle and setlists so turning on that boost when its solo time will be a breeze!
The AI will do all of the profiling including refining and setting up all of the input sense stuff and so on automagically.
At some point it will also learn how to brew coffee and go to this forum and delete "humor not detected" posts like mine
And for long rehearsal sessions : an integrated microwave oven , a beverage cooler and perhaps a pullout porta potti 
Cheers !
Sounds like a happy jam in the 70's , great mood !
Yep ... Brings back memories from after school day "rehearsals" in 1973 - 1974
Cheers !
In the Thon 3U case I had, the KPA´s 4 rubber feets had to be removed to fit into it ....
I think 4U is better for a powered KPA .
Cheers !
Main output L and R . TS cables .
Check the Manual for further info .. It is your best friend 
https://www.kemper-amps.com/downloads/5/User-Manuals
Cheers !
If the cable is not proper set into the mains jack there can be bad connection to the pins inside the plug
witch can cause sparks and excessive heat in worst case .....
And if the ground pin has no connection the KPA is ungrounded all together ! Nothing to play with ! ( Pun intended )
But seriously , fix that cable or get another one ......
Cheers !
I recieved my Kemper today. I have a question. It might sound silly, but I'm not sure if the power cable should be inserted all the way in the Kemper. Mine gets stuck halfway, and it won't go in any further. Is it normal? Maybe I should press harder, but I'm afraid I'm going to damage something. Here's a photo:
That is not normal ! 
And probably why it does not turn on ......
Unplug cable from wall socket and inspect if there´s any debris or plastic residue from manufacturing process, or bent metal parts .....
Cheers !
The important thing to remember is that every guitar you ever heard in a recorded song (from radio, streams, movies, etc) is the sound of a mic'd amp with it's specific EQ and Gain setting. You never hear the actual amp's cab on a recording.
Well ... not really ... How about lined guitars into mix desk, guitars into preamps -> into mix desk, Guitar into LA2A Comp / Limiter -> mix desk,
Rockman™ . Line 6 POD´s and other modeller´s and sim´s .... Acoustic guitars ....
I know what you mean and I dont want to mark words , but that was a bit far out
Happy New Year !
Cheers !
Hi and welcome ! 
You get the amp settings at that moment (a " snap shot" ) but it is tweak able to a certain degree afterwards 
Cheers !
The Manual is your best friend
Search "space" in Manual pdf .
Page 123 output section ( in Manual 8,5 )
Cheers !
Kemper monitor out -> 6,5 mm TS cable -> 3,5 mm adapter ( or if you have a 6,5 mm TS to 3,5 mm cable ) -> AUX input.
Start with low volume out from Kemper !
Also set "Monitor out" to "Mono" in output settings ....
Read manual page 41 (?)
Cheers !
OK, what happens if you DO have a pedal connected ? ( Expression pedal )
Other reasons :
Bad connection input jack / broken soldering joint on input circuit board ?
Oxide / dirt / dust inside "Pedal 1" input jack ?
Cheers !
Do NOT connect "speaker out" from Kemper to anything else than an unpowered speaker cabinet ( guitar cab )
or you might experience the smell of fried electronics .... in worst case ......
"Monitor out" is for powered FRFR speakers or other LINE signal gear .
Cheers !
I see you have "Mute @ Volume 0" checked ... Did you have any pedal connected to
"Pedal 1" and then disconnect it while it was at "zero" position?
The "Mute @ Volume 0" stays in that position even when the pedal is removed from
"Pedal 1" jack ......
( If you have Pedal 1 as volume that is ... )
Just a thought
Cheers !
"Oooh , look, a big balloon"
( I see two )
Is it really a "slamming guitar solo" in her bass pause / blank spot?
Sure sounds like a synth
Mary X-mas !
"Jag tror att stunden kräver .... "
From all of me to all of you
Cheers !
(.)(.)
Nice groove .... and a KPA on the floor
