Although he has a rather "thin" tone for a 335 ..... Maybe it´s the mix on my records ( vinyl )
And he use wha wha a lot , especially on LP "First Course" , and wha cuts a lot of the "full" tone
of course 
And it was a Wurlitzer not a Rhodes ..... Sorry 
Cheers !
Nice job Renaud : ) Really like the Rhodes piano sound.
If you´re aiming for Lee Ritenour sound , Rit 1 & Rit 2 era , you´re darn close 
Maybe some violins / strings in second half --> coda 
Might get "cheesy" .... don´t know ......
Cheers !
Strange EQ settings on output block ???
Well , you have to test with different headphones to sort out if the problem
is within the Kemper or if there is something wrong with the IEM.
Test one thing at the time and disconnect everything else.
Does the IEM run on batteries ? Battery status good ?
Too hot signal ? Line in or ..... ? Good quality IEM brand ?
Many factors to consider .....
Cheers !
How does it sound with normal quality headphones ?
Ohm is a factor , but mostly for the wellness of the amp ; too low Ohm
and the amp "thinks" there´s a short circuit in the speaker ( that can
happen if coil get burn and get stuck to the magnet ) and then nasty
expensive things can happen to the amp ......
But your speaker is 8 or 16 Ohm´s i guess, so no worries bout that 
And not a reason for that buzz ......
Cheers !
Yeah , that´s what I meant ; the edges of the magnet ( and voice coil ) in center of speaker.
At the edges of the speaker it´s just "rubber" suspension , no buzz there if the "rubber"
is intact and fresh ( not dry and cracked )
But the speaker is new , is´nt it
Warranty ?
Cheers !
Yamaha is reliable and has 3 (?) year warranty, but that´s not the right speaker ...
Try a DXR-10 ..... Recommended by many and sounds great IMHO
But there will be other opinions on that matter , believe me 
Cheers !
It sounds like the amp is distorting. A bad speaker should buzz at any volume.
Not necessarily . Depends on where the issue is located ...
Outer edge of magnet and high volume = long throw of coil = Buzz .
Outer edge of magnet and low volume = short throw of coil = No buzz.
Just one example of many ......
But as Muddy suggest : try with another speaker
Cheers !
Is that a home built cabinet ? Is there something loose in it ?
Hanging wires ? Loose screws ? Is the cab built with specification
for the speaker ? ( Vas )
Just brainstorming here
Cheers !
Hellu !
To my ears that "clean sound" sounds a bit distorted
and the following echo is an exact copy of that sound ,
with just a little bit lower volume of course ......
Clean sense setting ? Hot pups ? Low action , buzzy frets ?
Cheers !
Lock function ?
Cheers !
Have you tried to unplug "everything" and then put it together
one piece at the time in different order to determine witch
item starts the noice ?
And keep at least one item (KPA) grounded all the time !
Safety first ! 
Cheers !
Does it disappear if you unplug your guitar ?
Is your mouse wireless ?
I don´t think it´s a ground loop issue ( hum @ approx 50 - 60 Hz and @ 100 - 120 Hz )
more likely some electrical interference from ( mouse ? ) VGA screen, computer PSU,
dimmers , WIFI or whatever electric gadgets surrounding your workplace ....
Cheers !
Ok , probably power amp issue then 
And no warranty after 4 years ...... 
I hope you get it solved without going bankrupt ......
Cheers !
Halley halley ..
I guess you mean "output" ???
Does that ticking appear if you have your gear in
another room or in another house ?
If it´s OK from other outputs and headphones it
might be something with the power amp .....
Too close to other electric equipment ?
Computer, VGA screen , WiFi .....
Cheers !
I only use solid gold cables for the best quality sound. It's basically like a gold bar with audio jacks on both ends. Gotta get the best audio sound though!
/s
For real heavy metal guitarists and bass players i recommend Osmium cables 
Cheers !
Well , let´s say it´s "a freedom of choice" .....
If I want 8 copies of a rig with the same name,
it´s up to me , not Kemper
Imagine if it was like "Copy 1" "Copy 2" "Copy 3"
by default and no way to change it
Cheers !
Yeah , a bit confusing, to say the least
But there´s a "date and time print" to the new savings , right ?
Don´t know where to find them in the KPA though .....
Maybe in Rig manager .... Haven´t checked
I always add a " .1 " Or "Mod." ( Modified ) to a altered rig
when "Save as" ....
But not when it´s only volume related .......
Cheers !
Good evening .
Mogami is good but expensive
HOSA is good too and half the price
I have used many different brands in my P.A. profession
back in the days and most of the cables does a good job
as long as you treat them well , but don´t buy the cheapest
ones from China .....
And with balanced XLR there´s almost no risk of hum and
other noice ........
Cheers !
