damn, was hoping wouldnt have to get this one. how do they compare to the 2020 pack?
To my taste the AC20 Profiles are more voxy than the corresponding profiles in 2020 pack.
Posts by IngoRockt
-
-
I tried the AC20. I was looking for a chimey sound for tasty Vox-Sound. The search is over. (Let's look when I start a new search for my Vox-Sound
) -
An A/B external switch is a good solution of course, but it is an extra gear I should have to buy.. connect.. and not useing it so often..
I use Lehle 3at1 SGoS. I have Performances for each of my 3 guitars I need at gigs or rehearsal. The Lehle is connectet to my Stage (midi) and the Kemper switches to the guitar. On the Lehle-page is a video at the end which explains the function. The Lehle is setup in my stage case.
-
Display Morehave same issue since install of 3.0.145.16429
the rig manager won't load any profiles and i am unable to edit anything at all though i can add recent purchases etc
just can't load or edit them???
Windows 10 64bit with latest updates
How do i step back to previous version?
do i need to completely uninstall and then install an older version?
Will i then need to re-import all my profiles?
Only had the unit a short time and still learning, most important of which appears to be don't install new updates...
Thanks for any help you can give
Is Browser-Mode on Profiler aktivster?
-
This is a bad idea: Given a song with Intro, Verse, Chorus, Verse, Solo, Chorus, Verse, Chorus, Outro (or some more Verse/Chorus). The Performance is build up Intro on Slot 1, Verse on Slot 2, Chorus on Slot 3, Solo on Slot 4 and Outro on Solt 5.
Your idea is: Starting with Intro then pressing the switch turns on Verse pressing next time enables Chorus. At this point everything is ok. But then you need the Verse-Slot. By pressing the switch you enable Solo. That's not what you want. How to get back to Verse? You have to press 4 times to reach it. Your feature request only works with two Slots. But this can be done with a simple dual switch. Click left for Slot 1 and right for Slot 2.
My 2Cents to the feature request.
-
Ich denke dabei auch eher an den Soundcheck: mal schnell das Delay oder Reverb anpassen kommt schon mal vor....
Ansonsten hast du Recht, das ist Stress
-
ich habe schon fast vergessen, wie man das alles auf direkt auf dem Profiler macht. Der RM schafft Überblick und ist für mich leicht bedienbar.
Das birgt die Gefahr, dass du bei einem Gig nicht in der Lage bist, Einstellungen am Profiler vorzunehmen. Ich nutzt von Zeit zu Zeit auch die Einstellungen am Profiler, um nicht aus der Übung zu kommen.
-
In Output Menue the 3. softknop.
-
Yes, I have "Master Mono" all the time
You set it to "Send 1 Outout" or to "Main outout" or "Monitor Output"?
-
What are your settings for dircte output? You find it in Output-Menue on page 1. Try to set "Master Mono".
It is described on page 104 in the manual....
-
Unter My Profiler sind die auf deinem KPA gespeicherten Rigs, Presets bzw. Performances aufgeführt. Diese sind nicht unbedingt auf deine Festplatte gespeichert. Alles, was Donauwörth deinem PC gespeichert hast, wird unter Local Library aufgeführt.
Damit ist klar: am Profiler kannst du nicht in das Verzeichnis Local Library wechseln.
Änderungen, die du am Profiler vornimmst, sind nicht in der Local Library. Dazu musst du das Rig, Preset oder Performance in die LL speichern. -
Perhapst your smartphone disturbs. It sounds like this to me.
-
Danke IngoRockt, daran hab auch schon gedacht, direkt aufs Motherboard. Allerdings hab die Anschlüsse wieder hinten. Wollte eigentlich sowas wie ne USB-Patchbay auf`m Pult um ständig wechselnde Gerät ohne Turnübungen zu stöpseln. Kennt jemand sowas mit direktem Slot-Anschluss?
Leg doch einfach 4 Kabel von der Karte auf das Pult. Dann hast du alle Möglichkeiten.
-
Wenn du einen Slot im Pc frei hast, dann baue dort eine USB-Karte ein. Sowas z.B.
-
Try to morph the amp-gain.
-
I was going to use morph to boost every slot to a lead volume using rig volume as a control, so my clean sound can have a clean lead boost crunch can have it's own level of lead boost etc.
That's also my way to boost for solo. I did not notice an effect on the FX section. Perhapst because I don't use FXs that are sensitive to more volume.
-
Try a Fender-Profile (search the profiles from Martin Suijs in RM). Take a profile with some gain and turn back vol and tone on your guitar. Ad some reverb perhapst a bit of delay and it should fit.
-
No no, they is one in the world not using "copy-Paste" fuction like other, it is Kemper
I understand "Kemper is right other world is wrong"
The only solution is creating personal Nr to avoid Kemper bizzare databaseThe Kemper-workflow is logical: Usually a Performance is setup for a special song or a special situation. In case of one performance for each song in the setlist I name the slots with "Intro, Verse, Chorus, Solo, Outro" or something like this. In your logic you change in one slot (f.e. "Solo") a rig to get a better fitting to your sound, the name of the Slot will change from Solo to the choosen rigname.
For me that is not the way I want to act.
In case of setting up a new Performance with the given Effects and Fx of another Performance: Lock the Effects an FX and build up a new Performance by copy and paste the rigs into the new Performance. Don't forget to unlock before saving.
-
If you are a handyman I recommend this
-
Have you tried to lock the mod/x?
