Great tones. Keep up the great work!
Posts by danel59
-
-
Just a thought, would placing the pedals in an efx loop assigned to Slot 1 make any difference instead of running the pedals into the input of the Kemper? The reason I ask is I have experimented using my Ethos before the KPA and also assigned a loop in the stomps and preferred it in the loop. Also as above Definition, Clarity and some of the other amp
parameters can be your friend -
Hey no offense taken. The reason I set it up the way I described is for mainly recording. This manner allows me to have the Kemper or Ethos one at a time or both in parallel without having to change the guitar from one device to the other. For your purposes esp live the A/BY might be a better fit. Either way to answer your original question in a word would be "yes"
Cheers
Dan -
I understood your post all I was trying to explain is how you would get your guitar signal to both inputs of the KPA and your Engl without having to get an A/B switch, The outputs can then be fed to whatever you want i.e. Stereo power amp, two channels in a PA or two separate amps. In my case I use this idea into my audio interface for direct recording.
-
That should work with no issues other than connecting the two units (kemper and E350) One way that works is using the Direct out on the KPA to go to the E350 which can be set for dry guitar only. I don't use this live but I do at home with the KPA on one side and my Ethos on the direct out into my Interface and works great. I guess the only thing you would have to watch out for in this scenario would the possibility of a ground loop but that should be easy to work around.
-
Mats Nermark had a few profiles simulating the '80s Luke and Landau Clean tones which sound close to what you are looking for. You can check out his profiles on his website.
-
Not sure if this works for you, but I have the FCB1010 with Eurekaprom and have found that if I turn everything on at once(Via power bar) that it will not send info. If I leave the FCB1010 turned off until the KPA boots up then I don't seem to have the issue.
-
There is a loop setting for using a distortion device (pedal, Preamp etc) there is another one for delay mods etc. Best to read the manual
-
Yes quite easy. Same as any effect you can assign it to A,B,C or D and choose between mono or stereo and even Clean or Distortion
-
I would like Fuchs to do profiles. They did some plugins for a company I think Apoggee can't remember so would think they could do the same with Profiles. I guess big question of course is the manufacturer has to purchase a KPA which might be more than they want to invest also considering extra costs of interface gear and a dedicated area for profiling
-
-
Yes welcome! I agree that it would be great for studio but would be concerned about live unless you were able to tie the Kemper down
somehow (without looking to odd at the same time LOL) -
You can also assign the EQ pre or post in the Amp stack itself which can also make a difference in most cases. As posted above a different cabinet may be all you need but also fool around with the High and Low Shift as well as Pure Cabinet to see if that helps as well. Lots of good tips posted above as well
-
Suhr Thornbucker/Thornbucker Plus is another great option. I have tried Dimarzio PafMasters and 36th Anniversaries from Dimarzio. Long time ago had WCR Goodwoods and to be honest I didn't bond with them. The Suhr's are my current fave.
-
Thanks I haven't tried that yet. I just received a response from support and they said the same thing. Apparently a bug that is known if the KPA is attached to the computer with Rig Manager open
-
I just updated to the official release the other day and this morning I had a "Profiler system clock issue detected" come up. I took a photo and sent to Support and see what they say. I can still play it and tone and profiles seem fine. Anybody else run into this
-
For EurekaProm to undo press and hold Button 2 for approx 2-3 seconds
-
I have the FCB with EurekaProm and not sure that it will work as the FCB basically is now a dedicated controller for the KPA. You could probably replace the EurekaProm with the stock Eprom and then program it to run into the Motu and then send midi info to the KPA. I could be totally offbase and if so would like to hear from others as well.
-
Go to output menu and check the Main outs that they are turned up is the only thing I can think of right now
-
Would definitely like to hear comparisons of Fluence Classics vs Gibson PAF's
Thanks
Dan