Posts by f17f36fb62c62886946a9dfd3a5ef510b7cda077

Hello deadpan,

I also like to test theese profiles.
May I get them?
Your video sounds very promising!
Thanks

SOLVED

The hiss was caused by a power supply that feeds a pedal in the loop.
Strangewise the hiss appeared sporadically and at times the remote was connected.
Everything fine with kemper and remote.
Thanks

Hello,

when my remote is connected to the Kemper rack, hiss is clearly increased (no hum).
Without remote, there is no hiss.
I noticed this at home and in my rehersal room.
Has someone noticed this, too?

Dear net99,
I also like to say THANK YOU for your fantastic profiles.
Your Dual Rectifire profile is my absolute favourite of all commercial, free and rig exchange profiles.
It has that tone and less "noise" with moderate gain, which I prefer.
I use it for rythm, solo and the next recording

This is great!
Thanks

I already use momentary switches to rig up, rig down and morph.

I like to reduce cabling and gear with a remote.
Actually I run a cable snake of 5 cables to my board.
Two for switching.
One for midi.
One for power.
One for audio.
Therefore I wonder If you can assign rig up to a switch on the remote.
Without additional gear connected to it.
Otherwise i can keep it my way, because of no equipment and weight reduction.

Hello,

I assume it´s not possible, as I haven´t found this in the manual.
Can I assign the cc command "Rig up" for a Switch of the remote?
That would be nice for switching through rigs of a song with one button.

Thanks

Hello,

my rig contains a pitch-shift, delay and reverb.
I morph all theese and it works fine.
But when I put an additional stereo-loop in the x-Slot the loop does not work.
When I deactivate pitch, delay and reverb the loop works.
Of course I don´t try to morph the stereo-Loop. I just want to use a stereo pedal in the Loop.
In rigs which don´t contain morphing, the stereo-loop works fine.

Can someone help me?

SOLVED
I changed the stereo loop position with the delay position.
Suddenly all morphing was stereo.

Hallo zusammen,

ich möchte das Thema gerne nochmal aufgreifen.
Trotz der Gefahrenhinweise.
Hat jemand getestet per USB ein Pedal im Stereo-Loop zu speisen?
Mit dem "USB zu 9V Konverter Kabel"?
Kam es da auch zu unakzeptablen Nebengeräuschen?
Oder war dies evt. nur bei dem Line6 G30 der Fall?

Mein Pedal benötigt 9V DC, 100mA.

Hat sonst noch jemand so ein Kabel, welches er nicht mehr braucht?
[USB A (noch besser B) zu 9V, 2,1mm Holstecker, innen minus]

Grüße

Problem solved!
Thank you, guys.
I did not push the Morph button.
My last tweakings were long ago.
I forgot the two tables "Basis" and "Morph" to set all Parameters.
Once I pushed the Morph button all "M" appeared.

So long

Yes, I tried.
There is no "M" appearing when I turn Mix to max, like in the MOD Slot für the pedal pitch.

Hello,

I have a rig which already contains a "dive bomb".
It´s a Pedal Pitch that Morphs to -12 using a momentary switcher.

Can I also let a reverb morph into in this rig (from zero to a great hall)?
There is no morphing option in the effects/reverb slot.

So I assume this option is not given, or am I blind?

Thanks

Thank you

Dear Guido,
please give us a merged Mark V.
I my Kemper as much as I do because of your profiles!!!

Alright, thank you!
I barely use the power amp.
But to treat my Kemper well, I will shutdown via chickenhead.

Really???
That would be great.
Can someone from Kemper please confirm that this procedure causes no harm?

Hello,

I like to put my 3HE rack on the frontside.
(Our rehearsal room is super tiny.)
So I have access to the rearside from above for all wires.
I always switch the Kemper on and close the front lid again.
For switching off the same backwards.
It would be nice to not even open the front lid.
I thougt about cutting a hole into the front lid, but for better protection i like to have it closed.
Especially when it rains.

So could there be a simple trick to switch on/off from the rearside?

I assume pulling/insert the powercable while keeping the chickenhead to PERFORM is absolutely no option...

WE LOVE KEMPER!!!

Enjoy!

Website:
http://www.schakal-band.de/

Facebook:
https://www.facebook.com/schakalband

Youtube - Album Teaser:

Bandcamp (Full Album):
http://schakal-band.bandcamp.com/album/schakal-2

Pretty interesting!
But FOR ME it never supposed to sound like two amps in parallel.
I just like to have a symbiosis of VH4 and Mark V.
ONE new amp breed.
It was my fault to use the term "bi-amping".
And I was hoping to get the best of both worlds.
But now I see that the "blend" can´t be determined and the mixture could be the worst of both amps.
So I should look for another existing amp/profile that fits my needs.
Thank again for the discussion.

Everyone said "it´s not possible", until someone came and just made it.

Alright guys, you are the experts.
Thanks a lot for the discussion.

Every further advice is appreciated and will be tested with pleasure.
So long!