Hi guys. I want to have a setup in which our Cymatic LP-16 can be used to control my Kemper and switch between relevant patches. I have read this great article around the subject, but still don't fully understand what I need to do. I am using Reaper, and as I understand it I need to create a Program Change (PC) under event properties on my Midi tracks. So here is my question: which values do I need to insert in the Event Properties dialogue box? In my example here, i am using slot 3 and I need to switch between the 5 different patches within slot 3, meaning 11 through 15 (see attached files).
Posts by fclund
-
-
Hi guys. When I recently updated my Kemper, I made the mistake of changing my Owner Name. This resulted in me loosing all the favorites and ratings on all the profiles, that I spend so much time tagging. I have 800+ profiles, so it does suck quite a lot. Is there any way to see or bring back the Owner name I previously used? I haven't uploaded profiles to Rig Exchange, so that won't help.
-
Did you check (tick) this box? ... System page 5/18 - Wah\Pedal > Vol. (Top left soft button)
If unchecked the wah works but volume on other profiles doesn't
Nope I didn't - just did and now it works too! Thank you so much!
-
Here's how:
With the FC200 off ... press and hold the CTL (control) pedal then turn the FC200 on - (This is the routine for accessing the edit mode)
Andy, you're a life saver! Thank you so much! I have no idea what I just did there, but it worked!
The volume does however not work on the other profiles now. It's not a big deal, but would you happen to know why? It work before I made these changes...
-
Hi all. I tried setting up the FC200 midi board with my Kemper. It works fine for switching between the rigs. However the expression pedal seems to work as volume pedal per default. How do I configure the expression pedal to serve as wha? I am of course using a profile that has wha activated.
-
If you click on the Output button in the front panel of the Kemper, you can navigate to the SPDIF and see what signal is supposed to be going out of the SPDIF. It should be Master stereo if you want to use it for recording. Now go to the option of the audio interface (MBOX) and make sure that the session includes the SPDIF in.
looking at the picture you attached I see the volume knob (virtual) under 3 and 4 inputs (for SPDIF) is set to minimum, not sure if this volume rotary is an input trim that needs to be turned up to get sound in the audio interface!!
Keep in mind that the session or whatever MBX call it possibly template is set to 44.1KHZ as Kemper uses 44.1KHZ for SPDIF. IF you can't find the option, setting MBOX SPDIF to slave will insure it operates according to KPA sample rate at 44.1. Watch in the MBX Mixer for 3 and 4 as you play the Kemper and see if the meters do their thing to indicate they're fed and audio signal. If the meters don't dance, double check the connections.
Actually changing the Mbox settings to this http://screencast.com/t/pxXYIGKP4 made it work! So thanks so far, guys
For some reason the SPDIF track http://screencast.com/t/JY1DW5cjJqF (the bottom) one is recorded quite a bit lower than the tracks recorded directly through the input. I wonder why...EDIT: The reason was of course that the SPDIF volume on the Kemper was set too low. Now everything works intended. Thanks everyone for help!
-
Just checking....Is the SPDIF Output switched on in the Output section?
Is that the SPDIF Out LInk option that need to e checked in the Output section?
-
Is Profiler spdif out connected to Mbox spdif in and vice versa? Is Mbox set to spdif slave?
Yes - out connected to in and vice versa
I am however not sure if Mbox is set to slave. It's nothing I have actively done and I cannot seem to find a preset for that. Can you explain where I do this? -
Hi guys. New Kemper user as well as new to this forum
I've enjoyed my Kemper for about 2 weeks now, and I now want to start recording with SPDIF. For some reason this is however not working for me. I get no sound what so ever on the recorded tracks. I use Mbox and Reaper.
My Kemper is connected from the 2 SPDIF in/outs to the SPDIF in/outs on the sound card. The SPDIF volume in the output section of the Kemper is currently set to -9dB but I have tried pushing the volume in both directions in vain. In Reaper inputs have been set to SPDIF http://screencast.com/t/pqPjwFxfjy. The Mbox settings for SPDIF are like this http://screencast.com/t/VK73ZZIJoG4. If I try to record the Kemper signal via the input of the Mbox I have no problems. But as soon as I switch to SPDIF mode nothing is recorded. Any thoughts on what the problem might be?
