Posts by marianguitar

I have a big question: I use a special tool that has two tabs at the concerts. The bottom is a classic electric guitar and the top is an electro-acoustic ukulele.

http://mojagitara.com/pk-guitars-gitaro-ukulele-gu-1/

I would need the riga, which is meant to separate ukule from the guitar. In the current FW you can use SEND to include the effect loop, but!

1 / it's mono

2 / Effect loop can not be classified as reverb, so this way the rig would not only be mono but without reverb.

For example, in Line6 HELIX it is possible to define for each output what outputs to go and it is possible to send ukulele rigy eg. on the line (jack) stereo, and the guitar on the XLR.

I would very much like to use my Kemper for my tool, but I do not know how to solve it, so I'm asking if it is currently, or if the separation of outputs for each rig could not be applied to the new firmware.I will be grateful to every advice and help, with greetings

Ing Marián Marko
http://www.mojagitara.com
http://mojagitara.com/category…paratura/kemper-profiler/

Quote from Burkhard

yes, that is possible.

Thanks

Well, if I wanted to cut at least on MONO and I would use the effect loop on DIRECT OUT if I do not return from the signal to Kempra, then I would have the respective RIG play through DIRECT OUT MONO with the fact that the signal in this set RIG no longer going to the main line / XLR outputs ???

In Slovak:Dobre, tak ak by som to chcel vyriašiť aspoň na MONO a použil by som efektovú slučku na DIRECT OUT,ak sa nevrátim zo signálom do Kempra, potom by mi mal príslušný RIG hrať cez DIRECT OUT MONO s tým, že signál v takto nastavenom RIGu už neprejde na hlavné line/XLR výstupy???

Well, if I wanted to cut at least on MONO and I would use the effect loop on DIRECT OUT, if I do not return from the signal to Kempra, then I would have the RIG to play through DIRECT OUT MONO with the fact that the signal in this annotated RIG no longer going to the main line / XLR outputs ???

I apologize in advance for my English - I write it in a translator.Hello, I needed to advise:I have Kemper Profiler Rack and I use it to do a custom made tool (electric guitar + electro-acoustic ukulele in one).In the guitar, I have the idea that one switch selects which tool is currently playing. There's one cable at the entrance to Kempra. However, ideally, I would need to divide the outputs so that I guitar and ukulele Rigas point out separately.With Line6 HELIX, Loop also be included at the end of the rigu-chain and the necessary patches for the ukulele to point to AUX-1 and AUX-2 as optional outputs (stereo output for ukulele).At Kempery, I have come to a single thing so far, and that is the appointment of ef. loops behind the "X" module and pull the signal in mono mode for that ukulele. This is a solution, but:1 / the loop (at least I think) can not be classified as reverb2 / it's mono and I would like stereo.I will be happy for any advice ... marianguitar http://www.mojagitara.com
http://mojagitara.com/category…paratura/kemper-profiler/

In Slovak:

Ahojte, potreboval by som poradiť:
Mám Kemper Profiler Rack a používam ho k takému na zákazku robenému nástroju (elektrická gitara + elektro-akustické ukulele v jednom).
V gitare to mám vymyslené tak, že jeden prepínač mi volí ktorý nástroj aktuálne hrá. Na vstup Kempra teda ide jeden kábel. Avšak ideálne by som potreboval nejako rozdeliť (nastaviť) výstupy tak aby som gitarové a ukulele Rigy nasmeroval von samostatne.
Pri Line6 HELIX sa dalo ef. loop zaradiť aj úplne na konci rigu - reťazca a potrebné patche pre ukulele nasmerovať na AUX-1 a AUX-2 ako voliteľné výstupy (stereo výstup pre ukulele).
Pri Kempery som zatiaľ došiel na jedinú vec a to je zaradenie ef. slučky za modul "X" a v mono mode vytiahnuť signál pre to ukulele. To je síce riešenie, ale:
1/ nedá sa ten loop (aspoň myslím) zaradiť až za reverb
2/ je to mono a chcel by som stereo.
Budem rád za každú radu... MARIANGUITAR