Go to page 1 of the Master (Output) menu. There you can set the Main Output to Master Mono.
Posts by Kempermaniac
-
-
+1
Did you notice the amp parameters Clarity and Direct Mix? I know it's not the same as a dual-amp-setup, but I use them a lot on almost every profile with gain. -
There's a ducking parameter on the compressor, that's missing in my KPA...
-
There's also a function called "Store sets Favs" (or similar), which means, that stored rigs are automatically added to Favourites.
-
Right. But keep in mind: A snapshot is not like saving a rig. This can only be done by storing via the store button and "store as" or "replace". Also a snapshot is not accessable via browse mode and you can't assign a Midi-PC to it!
-
These are three things...
Edit: Ah, you've edited your post already.
-
Please check the exact horizontal position of your Profiler.
Haha, very good! -
With nothing plugged into the input the tuner bubble jumps all over
This is normal and has nothing to do with your input problem. Don't worry about that. -
That seems to be it guitarmaniac,unless i am missing something?
Off topic: Guitarmaniac is my nick at the german Line6-Forum. Do we know us from there? -
Thanks for the tip, but I'm feeling today a bit like your username (lazy...)
How do I set the wah pedal to channel 1 using the FCB only? no editor nor usb interface yet.
Greetings.
Matt.
Not channel 1, but CC#1! That's a big difference! CC = continous controller. Your pedal on the FCB must send CC#1. I don't own a FCB, but there must be some advice inside the manual. -
You don't have redundant rigs, that's a big advantage.
Plus the allocation is much easier in performance mode.
I will use it song based.
Ah, I see, thanks. So in PM you can use ONE rig with different FX settings, but in Browse Mode it is still only one rig, right? -
You're welcome.
-
Performance mode is truly great.
The possibility to play a rig with different FX settings is priceless and very well done!
In one of the next updates we will be able to use a simple stereo footswitch like the Boss FS6 to scroll through the rigs like with rig up/down in browse mode.
This will be even more awesome as it will minimize the controller footprint on very small stages.
Hm...I don't get the point. The possibility was there before. A different FX setting needs a second slot in perfomance mode (PM) as it was needing a different Midi-PC without PM. Or am I wrong? Where's the advantage in PM? -
Delay is only available post stack in the...delay-"stomp". There was never a delay pre stack!
-
how the hell I missed these, I'm not really sure, but they are great!!!! They really do a wonderful job. This was just what I was missing on the kemper, and it's been there all along. I use the low pass filter the most often, as I really didn't realize how much high end fizz are in alot of the profiles(not necessarily a bad thing, but just an observation). While cutting the highs at whatever frequency you want, it can also add as a slight mid boost as well. I run the manual around 8.1 or so, and the peak at about 1.0 or 1.1, this works generally well on most high gain profiles with my personnal favorite cabs. This kills all the nastyness up top, while making the profile much thicker and meatier in the midrange: It really is incredible. Turning it off and on shows how drastically better the low pass makes the profile sound. Try these out guys.
Thanks for the tip! I recently bought the Carvin Legacy profiles from TAF and was disappointed, because there was a lot of hiss on gainy settings. Sounding this way they were useless for me. But with Low Pass and your settings (post stack) they're sounding damn good! -
A bit too far for me...
-
Supposedly a sharp hiss with higher gain/volume rigs that have utilized the phaser.
And with some weird noise on feedback-settings above 50%. -
Thanks CK & Team and Andy!
P.S.: Geraldo is always a bit exaggerating it seems...
-
BTW: Excellent profile!
-
Yes, but you have to own a footcontroller, which has a seven pin midi output!