The Rig Manager manages rigs that are in your Profiler (aka My Profiler) and rigs that exist on the hard drive of your computer.(aka local library/rig exchange)
You can audition each rig by doubleclicking it in the Rig Manager. When you do that the rig is being transfered from the Rig Manager to the editbuffer of the Profiler. You do not need to store it there in order to preview it.
Nightlight beat me by a second!
Posts by Kemper Support #1
-
-
As long as you are finetuning your slots in a performance please use the rig buttons on the right side of the Profiler to navigate between the slots. This will preserve the changes and you only need to store the performance once before you load another one.
-
I would say I'm sorry for the title, but honestly, it doesn't even begin to convey the amount of pure hatred I have flowing through my body right now for this system. I'm at the point where right now, all I really want to do is find whoever designed Rig Manager and punch that person in the face.
!
Threatening one of our stuff to physically hurt them must be a new low in the history of this forum.
I would suggest you consider to apologise for this and edit your post accordingly. -
I tried again and it didn't work again, but then I used another stick and with that, it worked. Really strange, because the other one works with any device (from PC to Mac to PS3 and whatnot). Ah well, got it to do what I needed, so that's the most important thing.
Could it be the formatting, though? I formatted the other stick on my Mac in Mac OS Journaled, and the one that worked was an old one I had laying around that was formatted on Windows in FAT32 or NTFS (not sure).
THe Profiler can only deal with sticks that were FAT32 formatted. -
Please send an email with a backup to [email protected] with a description of your setup and how the problem can be recreated.
-
make sure that you are using the return input and not the alternative input on the back of the Profiler.
-
The converter can probably work as a clock slave. The Profiler needs to be the master in a digital environment.
-
here is a list with some useful tips.
http://www.sweetwater.com/swee…shooting-wont-reactstart/ -
When you restore your backup you will also restore the global settings.
The greyed out performance is caused by the fact that the default setting for performance load is pending.
Go to the System menu and select the performance load mode that you prefer. -
Starting with the System button pressed down only clears the global settings. Starting with the Rig button pressed down will initialise the edit buffer. Different scenario!
-
Even if the Profiler would allow you to use the S/PDIF in as the AUX in you would still need to run a second S/PDIF cable back to the Macbooks S/PDIF input and set the Macbook to be the clock slave.
-
The error message that you get points to a problem that could be fixed by starting with the RIG button pressed. No need to restore your backup as the reset will not alter your data.
-
Start your Profiler into Browse mode while holding down the RIG button until you se "Initialising current rig" .
This should fix the issue without altering your data. -
The S/PDIF input is only available for reamping purposes.
May i ask what monitor mixing console you are using? -
As stated in the Profiling guide you can connect a microphone or a microphone amplifier to the Return input of the Profiler.
Thats on page 13 in the chapter "Making connections". I would recommend to read it more thoroughly. -
Basically yes-you need to assign the pedal in the system menu of course and calibrate it.
-
Only one pedal can be used to morph at the same time but you can use the same pedal with the Remote at one time and at the back of the Profiler at another time.
-
Effekte können nicht gelöscht werden Wenn versehentlich ein Effektpreset gelöscht wurde kann man dass wieder importieren in dem man den Factory COntent 4.0 von der Kemperwebseite herunterlädt und von dort das Effektpeset auf einen USB stick kopiert, der zuvor mit dem Profiler formatiert wurde. Das Preset muss in den Ordner SHARED kopiert werden. Anschließend kann es mit der Export Storage/Import Funktion in den Profiler importiert werden.
Harmonizer Effekte heissen im Profiler Pitch Effekte. -
It seems that simply the backup lithium battery for the realtime clock inside is empty and has to be replaced (see picture!)
That would not explain why the message went away after the update and the appearance of the other problems that followed.
-
the Remote is available as a separate item in the Kemper online shop with free shipping, 36 months of warranty and 45 days money back policy
http://shop.kempermusic.com/in…ories/295/profiler-remote