Posts by graoully

OK. I use the head with a Focusrite usb interface. So, I can adjust the sound level coming from the profiler head to get the good balance between the guitar sound and the signal coming from the computer. I don't know how to mange it using the USB audio function (that's what I do with the stage, no dedicated soundcard). When I try to adjust the levels for all the rigs (meaning not using the rig volume for each rig), both guitar and computer levels change.

So my question is how to balance the two signals, how to adjust them independently ?

Hi there

I noticed the head boot time is way longer compare to the stage. I don't understand as I thought both have the same hardware and software can't be so different.

Any clue ?

I faced a slightly different issue. I copied all my performances from my profiler head to my new stage. It turns out all the rig volumes are higher, don't know why ?? Changing all the rig volumes of all my performances one by one is kind of a P.I.T.A.

Using the Master volume doesn't help cause I use the USB audio function and then the signal coming from the computer change evenly.

I definitely need this global rig volume adjustment.

Seams there's no answer ??

Hi There

I'd like to plug a microphone into my stage. I've read the user's manual, had a look at the USB audio video from Kemper and searched for advice on this forum.

Here's what the manual says :

Recording external audio sources

Additionally, you could use the PROFILER as an audio interface for external signal sources such as a microphone.

For this application, set Record Source (Rec. Source) to “Return Inputs” on the PROFILER Head and Rack to feed the signals of the RETURN to channel USB 1, and the ALTERNATIVE IN to USB 2. Stage users should set either 1+2 Source or 3+4 Source to “Return Inputs” and feed the signals of RETURN 1 and 2 to their DAW.

So, I connected my mic to return 1 but in the output section of RM, I didn't find "rec source" shown in the video. Instead there's 1+2 Source and 3+4 Source. I guess this is the stage configuration, so I chose "Return Inputs" in 1+2 Source. I can here the voice only if I use my DAW. Is it a normal behaviour ?

Lately I tried something different. I wanted to transfer the rigs only (profiler + local library) and keep the stage general settings . Then I used the "restore rig manager content", and selected the last backup from the head. Surprisingly, I got a message saying "the local library will be overwritten". It turns out the rigs in "Myprofiler" didn't change.

New try : as I made a copy of these rigs in a folder of my local library, I made a copy/past in the profiler folder. Some of them were copied, but for the others, I got a message saying they were "damaged".

Any idea ?

Sorry I should have written events chronologically.

First, I tried the "Access point mode", my phone found the profiler and I had a direct link between the two devices.

Then I tried the connection through the network. As the WPS procedure didn't work, I entered the SSID and PSW manually. Then, while the profiler was connected to the WIFI (the SSID showed up on the display), Android RM didn't find it.

It works for me with the "Access Point Mode" too, but I guess it should work through the network if the stage and the android device are connected to the WIFI ? I tried, it didn't make it, RM keeps on searching for a profiler.

I tried to connect the stage to the router thanks to the WPS process. Pressing the WPS button on the stage did nothing. The light of the WPS button is not as bright as the other buttons, don't know if it's normal ?

Hi there

I plug my profiler head into a Scarlett 6i6 2nd gen. I had some trouble for month using the SPDIF (clipping), so I switched to analog (inputs 3-4 for the Scarlett). It works quite well, but time to time, the Scarlet loose my preset (3-4 input doesn't show up on the interface, so i need to add it). I asked Focusrite support. Let say guys from kemper and Native instruments support are way better. Same problem with every Scarlett software release.

Any clue ?

Hi there

I read a couple of posts about it but quite old. Simple question : assuming both have the same release, how can I transfer all my settings (including the rigs) from a head to a stage ? I guess it can be performed with RM ? At least I might backup the head rigs and restore into the stage ? I noticed some settings are slightly different on the two profilers.

But this slot is used on my profiler head to connect the remote.

How can we connect rig manager on Android with a profiler head ?

You can drag and drop your rig, part of the performance into MyProfiler at least witn RM 3.4.51. It takes 2 sec.

Hi there

I've got a message saying Rig manager can't find my profiler. It's not the first time, but I always fixed it. Today nothing works. I changed the USB cable (B/A), reinstalled RM, switched ON/OF RM and the profiler.

Any idea ?

New updates today.

And I tried to report the issue (Beta test portal), and got an internal error 500 !

I tried to change one of my rig settings in performance mode and saved it. Then after switching the profiler off and on, I got the older rig settings, not the new one. I did it twice, same issue.

What is this morph colorded "thing" ?

My kemper is connected to a scarlett 6i6 thanks to two S/PDIF cables. I had some trouble some months ago, the sound was fine when I connected my headphone to the Kemper headphone connector, but very noisy when I connected my headphone to the scarlett headphone connector. I lowered the S/PDIF level until the noise disappeared. Since the last update, it is noisy once again. Then you understand why adjusting this level is mandatory.

Quote from gtrplayr85

Can you please post a link of this video? I'm fighting this same battle at the moment.