The ground lift settings of my Stage survive a restart. This includes the Return ground lifts.
I tested with the latest OS.
By the way the output settings are global and don't need to be saved nor do you need to create an Output Preset to make those stick.
ahh thanks for the reply , yeah I just updated to the newest OS and it now stays on. Think I was on 7.3 or 7.5
Hey, I turn on the (return 1/2 lift) button and it won’t save. So when I turn off the Kemper stage and turn it back on, it isn’t on. I’ve tried saving it as an output setting but that doesn’t work. It is unaffected by the saving of the output settings. I need this to work because I have buzzing if it isn’t turned on. Any help is appreciated, thanks.
Have you contacted support??
yes just opened a new ticket
does nobody else have this problem?
Display MoreHi BigP1998
I haven't found a mail regarding a replacement in our system.
I have been in contact with you and we wrote about your settings, but didn't get a reply to my last 2 mails.
Please open a new ticket.
Just opened a new ticket
OK... I'll check with support tomorrow and see if we can find-back your ticket
Thanks
Display Moreplease check your spam folder.
just as a note again: the Stage works fine as SPDIF slave with the current release (7.1.12)
there are a lot of variables which can mess up correct digital audio I/O on a computer.
for example: to rule out for driver and buffer issues on your DAW, you could try to record with a simple loop-back cable (directly between the SPDIF-out and the SPDIF-in of your interface, with the same settings you're trying to record the KPA)
of course: maybe there is a defect on your unit, that can be ruled out by exchanging it.
Support should always contact / answer you.. maybe something landed in a spam folder?
Thanks for the reply, I appreciate it. Just checked my spam folder, didn't recieve a message.
I have figured out that the pops and clicks when I switch rigs only happen when the rig is using an effects loop (no pedals just a brand new 6in mogami gold cable to connect the send and return), this leads me to believe that there is something defective with the effects loops. I asked for an exchange with a new unit 5 days ago but they still haven't replied yet.
I still do encounter pops and clicks when using spdif (interface set as internal/master. Interface, kemper stage, daw, all set to 44.1khz and kemper stage set to auto). also using latest firmware and good high quality RCA cables. I asked for an exchange with a new unit 5 days ago but they still haven't replied yet.
where do you set SPDIF to auto?
I was under the impression that the kemper stage could be used as the slave. Is this true? If so then I must have a defective unit because there are pops and clicks when using it as the slave with SPDIF. Any input is appreciated, thanks.
Is this normal? Does anyone else have this problem? I read through some past forum posts about this topic and I couldn't find a solution to the problem. I have had this problem on my 1st Kemper stage and now my 2nd. It is pretty noticeable.
I was browsing though rigs and the kemper stage just froze, none of the switches worked and it was like that for about 10 seconds then the screen went to "KEMPER PROFILER" and it has stayed like that. It still shows that as I am writing this right now. Also when first turning it on today it was just frozen at a blank screen and I had to turn off my power strip and turn it back on. Let me know if you have had this problem, thanks.
update: tuner button did not work a couple times as well
Jesus, I've got the same problem with just one of those buttons. I've got a ticket open but it does not seem to be going anywhere. But you man are super unlucky having had to return 1 unit and receiving this. Is there really no QC on their end before they ship out?
They told me that they were "pulling a new one, testing it again, updating it" but when I received it, sadly it still had problems (tuner and bank buttons not working sometimes).
Display Morejust grabbed the manual for the FC7: it's a 50k potmeter on tip.. this should work fine with the KPA. I'm not sure wether it should be set to type1 or type2 right at this moment (have to check) but definitely one of those type settings should be OK.
so:
please set type to type1, press 'calibrate' and move the pedal several times up and down
if this doesn't yield the required behaviour, select type2, press 'calibrate' and move up & down
it's not needed to 'save' or anything after this
Thanks, I was using type 1 and type 2 works way better but it still doesn't use the last 10ish% of my pedal travel on both the top and bottom. But it is more useable for sure.
My 2nd kemper stage that I just recieved as an exchange for my 1st one that I have had major problems with. Up bank button doesn't work *roughly 80% of the time.
According to this picture, the FC7 has a TS cable. It is not wired with a TRS cable, like a standard expression pedal, as expected by the Kemper.
My yamaha fc7 has a trs cable, I would show you a picture but the file size is too big. You can find a picture online with a trs tip aswell.
did you set the 'type' of the pedal correctly, and did you do a 'calibrate' ?
Yes
