Posts by EpiphanyOfMusic

Well Cubase did it for me haha

Question: What if Spdif output is Stack?

Also I dial up Reamp Sense and it does nothing

Let's say my return signal is low. Transients small and I wanna raise the level coming back in

Reamp Sense don't do it

I figured it out haha. used Cubase Presets that got it working. Saved them and writing down every fucking thing so this never happens again

Here is a Link to a YouTube Video I made showing exactly my settings and what I am doing. I hope this can help cause I still can't get a D.I to ReaMp

PS. I also tried swapping out OutPut bus to Spdif Right, and swapping out connections it isnt working

Maybe I'll make a YouTube video showing exactly what I'm doing from scratch so you can see in real time

Setup
D.I Input Stereo Output Spdif Left
Reamp Input Spdif Left Output Stereo
Kemper set to return Spdif Input
Kemper output Spdif Stack
Clock source set to.kemper

Symptoms
REAMP track is duplicating the D.I track
Reamp track shows line levels so somethings going on
Monitors I hear nothing
Headphones to Kemper I hear D.I going through Kempers profile

Spdif is fine its sending back a signal just its returning the D.I back and its only coming out of the headphones

Clock Source is set Externally in DAW and Spdif in Interface

I just can't figure out what's wrong that it won't send back an AMP signal

Question does the clock source have anything to do?

Interface Clock source Sodif
Daw :Externally Clock Source

On d.i Reamping Output=spdif Left?
Recording track input= spdif right?

Nightlight can you cbdcke my newer post with pictures and tell me what I did wrong for reamp

To make things simple
D.I Input =? D.I Output =?
Reamp Input=? Reamp Output =?

So make the input of track 5 spdif input left?

NightLight. Yes I am getting Signal Levels and I hear it out of my Headphones.
Also as you can see in the Photo. It's duplicating the D.I Signal (Even if I use Output Bus Spdif Right)
Here is my exact Settings.

Kemper Input: Spdif Input Reamp
Kemper Output: Spdif Stack

My DAW

[Blocked Image: http://i60.tinypic.com/2ildgg7.png]
[Blocked Image: http://i61.tinypic.com/64nri8.png]
[Blocked Image: http://i60.tinypic.com/5vtbfd.png]
[Blocked Image: http://i58.tinypic.com/soo4zs.png]

I settled with the Complete 6. So far it has been giving me the best luck

Spdif Left (Reamp In is the Mono Output Bus Spdif Left) in VST Connections

I figured D.I is Stereo. Sending out Spdif To Kemper via Output Bus Left(Reamp) then

The New Tracks In (Reamp being sent through Kemper)

And Stereo Out to Hear it

Awesome. Any idea what is wrong with my ReAmp config that I cant get the D.I to come back ReAmped in the other Audio Track?
I hear the D.I Reamped through my Headphones. It just won't come back through my Monitors or into the Actual Track

Once again
Created A Mono Output Bus Titled "Reamp" and it is Spdif Left
D.I Track (Stereo In/ Reamp (Spdif Left) Out
New Audio Track Reamp In/ Stereo Out

Alright so I got Tracking A D.I & Kemper nearly mastered I just need to figure out how to increase the output volume to the Right SpDif (Amp Channel) I use Clean Sense to raise the D.I Level going In

I am still stuck at Reamping. Once I figure out how to Reamp a D.I I am content
Here is what I did
Created A Mono Output Bus Titled "Reamp" and it is Spdif Left
D.I Track (Stereo In/ Reamp (Spdif Left) Out
New Audio Track Reamp In/ Stereo Out

I hear nothing though
I also set the Output on Kemper to (Stack)

The Input is Spdif Return Input

Stereo out

Okay guys so here is exactly what I did and how it isn't going right

I followed Night Lights Setup. Created a Stereo Bus (Spdif Left, Spdif Right)
Created 2 Audio Tracks in Mono. 1 Input Spdif Left, the other Input Spdif Right (To monitor)
When I turn on Monitoring for the Right Channel, it goes nuts and makes loud feedback screeches

When I track the left channel tracks Clean & Effected
The right channel tracks a amp channel that sounds like it's underwater

Git Stack as my Spdif Output