I have a kemper stage and a Fender Hot Rod Deville Michael Landeau (2x12" Celestion VType) connected directly to power. To me, sound great. I Like it. Its all I need.
Posts by guilleguille
-
-
-
My distortion sens has been at 0.0 for over 3 years. I use 10 guitars. Each one different.
Me too (only 3 guitars)... And sound great.
-
I have had the same noise problems in all profiles and they appeared since version 10 of the software.
I have had noises in all the guitars all week and as soon as I went to previous versions of the software, the noise disappeared.
It's something they should fix in the latest version.
I Think you are right. Early versions had not this problem
-
Thanks for your reply.
The thing is , I'm on firmware 10.1 , why would I have such issue ?
The same
-
I have the same problem till updated to FW 10.0 my stage. There´s a bit of hum in any level of gain, no matter if is clean or cruch.
-
Thanks a lot. I´ll try.
-
Happy New Year
It's a New Year, that must mean it's time for a new stab at the old Randy Rhoads re-issue White Marshall 100 watt head ( it's freakish loud ). I also don't think I ever did it justice in the past, so here we go again. This time I'm trying 2 x Marshall 4x12 cabs each with the Fredman mic technique. That's 4 x SM 57's with the 55 degree angles as shown in pic.
Profiled with and without an Ibanez TS 808 tube screamer. I used the channel 1 in, which means the volume 1 & 2 were cascaded, with volume 1 at near 10 and channel 2 at 8 or so. I mean this thing was dimed. Voltage set to 112 volts using bucking transformer. I gave in and put the Boss Waza tube expander between the head and cabinets cause the volume was nuts.
Maybe these work for you ? Maybe they don't....Patches are in the RE.
-Wht Marshall // the starting point
-Wht Marshall boost // non boost profile with kemper boost pedal internally added
-Wht Marshall Overdrive neutral // profiled with ts808
-Wht Marshall Overdrive most // patch just tweaked up to give more juice
Thanks a lot.
-
Your current Rig Manager will suggest an update to 3.3.50 which is a release revision and handle the upgrade if you confirm.
If you havn't installed Rig Manager yet, download the latest version at the KEMPER download page and install that revision. It will suggest an update as needed.
But my problem is that; it does not install Rig Manager.
-
you should post these messages here.
I attached information about failed install. I hope be useful
-
With this it should be no problem to install the latest version. Download it and let it install itself. Before, make sure your former version should be cleanly deinstalled. Delete all entries if deinstallation did not work well.
Thanks CarloLf. I already tried three times and didn´t work. Show the same message.
-
What version of Windows are you using?
Hi. Windows 10 professional
-
Hi. Where I find Rig Manager 3.3.50?
-
Hi to all Kemperians!!
I did not used RM (3.3.38) for a while and today when open app on windows says that some elements are missed and I must repair. I did every single instruction and nothing. Show the same message. Uninstalled RM 3.3.38 and installed 3.3.47 but show, again, the same message. Anybody know what can I do, please?. Sorry about my poor english
-
Hi. I have a Kemper Profiler Stage. I use Rig Manager only to load any new amp. All the tweeks I make directly on Kemper Stage. This way, when I need make some change while I´m playing in rehearsal or shows, is more simple.
-
when you drag a performance from Rig Manager to the "My Profiler" location you are copying the complete performance including the rigs in the 5 slots.
Thank you
-
performances cannot be imported from a USB stick. You need to use Rig Manager for this task.
Hi. Does it means that a performance also import 5 rigs?
-
Thank you very much
-
Thanks a Lot, Chop Tones for this gift.
-
Hi. I use the kemper and tube amp (Fender HotRod Deville Martin Landau) for rehearsal and live. The Stage is connected to amp input directly. Sound great. To record at the studio only Kemper Stage.