In Browse Mode is it possible to browse for a rig using the KPA then assign a rig to switches 1 through 5?
Assign Rigs to Switch in Browse Mode
- paltomare
- Thread is marked as Resolved.
-
-
In Browse Mode is it possible to browse for a rig using the KPA then assign a rig to switches 1 through 5?
In Browse Mode the Remote switches in views of 5 rigs.
You could browse for certain rig, give them a number like 01rig, 02 rig, 03rig etc. and when these are in view they will be switched.
Bank 1 would be: 01-05
Bank 2 would be 06-10
...
and so on. -
So if I want to store 5 of my go-to rigs it would be best to set up Performance Mode it seems.
Thanks. -
So if I want to store 5 of my go-to rigs it would be best to set up Performance Mode it seems.
Thanks.
Yes, Performance Mode is much more convenient when using the Remote. -
Thanks, I'll give it a try.
-
Following up to my original post. I now have 5 of my fav rigs assigned to a single performance called My Rigs. While in Performance mode I don't see how I can switch effects on or off when in one of these rigs.
For example, when in Browse mode I have effects assigned to remote bottons for a specific rig, but when I switch to Performance mode I do not see, nor have control over those effects when in the same rig.
I must be doing something wrong. -
Following up to my original post. I now have 5 of my fav rigs assigned to a single performance called My Rigs. While in Performance mode I don't see how I can switch effects on or off when in one of these rigs.
For example, when in Browse mode I have effects assigned to remote bottons for a specific rig, but when I switch to Performance mode I do not see, nor have control over those effects when in the same rig.
I must be doing something wrong.Little tutorial for you on Performance Mode and The Remote... Good Luck!!
Check this out: https://www.youtube.com/watch?v=X5_iafCGAQ8
-
Thanks, that link was helpful. I didn't realize the rig in the Performance slot was a copy of the original rig.
I now have effects stored to buttons for each rig, however, I still do not see the effect shown on the top of the remote screen similar to what I see in Browse mode.
Is that a setting somewhere, or is that not possible? -
In Performance Mode you can chose between two display layouts on page “Remote Settings” in System menu.
-
Perfect, Layout B is just what I was looking for, thank you.
-
Great! I use Layout B, too.
-
Me too on layout B. I just wish the Remote didn't have such a low contrast cheap LCD screen especially for $600 .I did an outside 4th of July gig on a lake tonight and the screen on the remote was totally useless. NOT HAPPY
-
Me too on layout B. I just wish the Remote didn't have such a low contrast cheap LCD screen especially for $600 .I did an outside 4th of July gig on a lake tonight and the screen on the remote was totally useless. NOT HAPPY
Layout B also. Was it the sun that washed out the screen or polarized sunglasses, cause I can't even hardly read my smartphone screen with Serengheti polarized glasses. -
You can use you foot to put the display into a shadow.
-
You can use you foot to put the display into a shadow.
Haha, leave it to paults!! Our own MacGyver -
LOL! I started using this idea with many previous MIDI controller pedals.
Or, you can also make a shade out of cardboard, if you prefer not to use your foot to block the direct light.
-
I like the suggestions ,but I find the contrast lacking even on dimly lit stages. Part is they try to crowd a lot of info on a pretty small screen
-
thanks..
-
[quote='paltomare','http://www.kemper-amps.com/forum/index.php/Thread/22224-Assign-Rigs-to-Switch-in-Browse-Mode/?postID=237011#post237011']Following up to my original post. I now have 5 of my fav rigs assigned to a single performance called My Rigs. While in Performance mode I don't see how I can switch effects on or off when in one of these rigs.
For example, when in Browse mode I have effects assigned to remote bottons for a specific rig, but when I switch to Performance mode I do not see, nor have control over those effects when in the same rig.
I must be doing something wrong.Little tutorial for you on Performance Mode and The Remote... Good Luck!!
Check this out: https://www.youtube.com/watch?v=X5_iafCGAQ8[/quote] .............thanks for this
-
In Browse Mode the Remote switches in views of 5 rigs.
You could browse for certain rig, give them a number like 01rig, 02 rig, 03rig etc. and when these are in view they will be switched.
Bank 1 would be: 01-05
Bank 2 would be 06-10
...
and so on.......thanks ingolf