Hello guys this is the 2nd song of my new album Death Construction. For the album I used JMT 2 profiles but I had to tweak them very very much to get a decent result. The profiles are not even close to JMT's promo videos.
External Content
youtu.be
Content embedded from external sources will not be displayed without your consent.
Through the activation of external content, you agree that personal data may be transferred to third party platforms. We have provided more information on this in our privacy policy.
Posts by silkof
-
-
if the DI signal that is being sent back to the Profiler has a lower level than the original guitar signal the resulting sound will have less gain.
The correct parameter to compensate for that is the reamp sens parameter.
Make sure that your DAW or audio interface is not attenuating the signal on its way back into the Profiler.
My guitar's input gain makes the kemper go to yellow at times. Having the AI pream at a point where my input signal slightly going to yellow make the reamping sound similar. So I guess this was the trick. Thank you man
-
Hello there,
i've having some issues with reamping. My gear is
Audient ID 22
spdif from ID22-->Kemper spdif
Kemper xlr main output--> ID22 input 1
Kemper direct output jack unbalanced --> ID22 input 2
I record both DI and wet signal to 2 different track with the following settings
Monitor output at Master mono
Direct output at Gt studio
Clean sense at 0Distortion sense at 0
If i increase clen sense the input led goes red...so I leave it at 0 and it goes only yellow sometimes
Then when I reampa I get the following result compared with the wet signal
1. Wet signal (not reamped)
https://www.dropbox.com/s/xe8d…0xlr%20input%201.mp3?dl=0
which is pretty good I like it but then...
2. Reamped with Dist sense at 0
https://www.dropbox.com/s/kx3c…ck%20unblalanced.mp3?dl=0
which is very weak it sucks
3. Reamped with Dist sense at 7
https://www.dropbox.com/s/syc5…ck%20unblalanced.mp3?dl=0
mediocre result
4. Reamped with Dist sense at 10
https://www.dropbox.com/s/9m1c…ack%20unbalanced.mp3?dl=0
which is pretty close but I would say less alive.
Am I doing sth wrong? Why do I have to crank up the dist sense to get a decent result?
Thank you for your answers -
what’s the Develop Device ones like? I saw their Triple Rec profile pack but didn’t buy it. Any good?
I bought engl savage and the high gain amps pack...I m not very impressed. The last one that I was amazed of was colin richardson's pack.
-
No profile will be universally mix ready
I ve learnt this lesson.
-
How to Reamp Kemper with Reaper (non-SPDIF Method) Tutorial..
That is my favorite thread
. Read to last post. It might give OP some help.Well I dont use reaper. I managed to reamp using cubase but the quality is much worse comparing it to when I record. I wonder if spdif has better quality.
-
Guys I just bought a lindy converter as well and I just saw that I can only use my 1 device for one purpose not both. Will the DI be of better quality if I use the converter to send to my ID22? Or by using the xlr cable is the same?
-
I've been trying to find mix ready profiles that sound good. Did anybody try these ones?
-
compare the Rig settings in RM and the Profiler. Do they match each other?
compare the output section values. Do they match each other?Now I see that in the output section there is a pure cabinet section as well and yes they match.
But is it normal when I record to have a different sound that what I hear from the monitors? -
you can set Pure Cab for each profile or globally
When in the rig manager is at 0 and in the kemper at 3.1 which one is the active one?
-
Hello guys,
I have an Audient 22 to which I connect the kemper through xlr cable from the left main output. In the output section the main output is at Master Mono. Main volume is -6db. When I record my sound is more fizzy and whith less body than what I hear from my monitors. Should the sound be identical?
Another strange thing is that I connect the kemper to the pc with a usb cable and I have the Rig Manager open. In the setting of the profiles the pure cabinet is at 0 but in the kemper when I go to page 6/8 of output section the Pure Cabinet is at 3.1. How is this possible? What is the true value?
Thanks for you help guys. -
Are you asking me?
-
-
So if I record it as it is (very low volume) and then send it to return input for reamping it wont need any boosting and it will be like I'm playing my guitar through the front input?
-
Guys I try to record a DI and a profile at the same time. I have everything connected. From the output I have unchecked / unlinked all the "volumes". My direct volume is lit out and when I trun the knob the volume isnt affected. From rig manager the Direct out is set to Guit Analog. It lights on only when I change it to Stack or Mod or Master...But I want a clean DI wihtout any effects to be recorded. How can I add more volume to Direct out when is set to guit analog?
-
Ok I found out that I should import all the profiles to "My profiler" in rig manager in order to be able to see the cabs. If I have them in Local Library the cabs are not available for selection from the kemper.
-
GearJocke yes this is what I mean. I switched from presets to rigs but I see only cabs from other sources (not middleton's pack). I find only 1 of middleton's cab and it's from one of his profiles which I tweaked a bit and saved it with a slightly different name. I cant find none of the other, not even those that are loaded automatically to his profiles. When I go to cabs -> rigs and use the browse knob there are 288 cabs and only 1 is middleton's, the one I tweaked...? How can it be possible profiles to have the cabs loaded on them but I cant find them in the rigs list?
When I extracted middleton's pack there were 2 lists of files with the same name and extension but different size. Is it possible that one list is only the cabs of the presets but I didnt load it?
-
Guys why when I press the Cabinet button as in Middleton's video I dont find the cabs of his profiles? I can find 288 cabs in my kemper but none is from the Heavy Bundle 2 as in Middleton's video...how is that possible?
External Content www.youtube.comContent embedded from external sources will not be displayed without your consent.Through the activation of external content, you agree that personal data may be transferred to third party platforms. We have provided more information on this in our privacy policy. -
I would use XLR. There is no TRS output on the KPA it is an unbalanced TS. It will still work with a TRS cable but you still don’t get the extra 6db gain or balanced signal for noise rejection. To get the same level from the TS output as XLR you would need to run your interface gain at +6 not 0
Ok thank you man I think the problem is solved now:P
-
No...minus 10 dB to plus 50 dB for your line inputs. Meaning you'd have to dial 10 dB up from that to get to 0 dB.
Or did you mean you did exactly that and got peaks at -8 dBFS? That would mean just 8 dB of headroom in both units, which is more than high enough...
You can't drag a guitar tube preamp into the equation
It's a very different thing. And it's not like higher voltage out = better quality.Yes this is what I mean with +10db from the preamp I get -8db with TRS cable.
Why not use XLR with line in?
