Conceptually, you don't store anything on the Remote, but the Remote is a remote control. You create your sounds and performances on the PROFILER and use the Remote to load those.
Posts by Burkhard
-
-
There are two limitations to this idea:
1. Parameters could be modified to an extent, that this statement "based on preset A" is meaningless or even misleading. The current settings could be closer to another preset.
2. Presets are user data and not hard-coded. You can delete presets, you will be able to modify and replace presets or rename presets in OS 7.0. Rigs can be shared without "their" presets. So, this message "based on presets A" could lead into the woods.
-
Why can't you distinguish a Vintage Chorus from an Air Chorus? The effect type gets displayed on the left hand side within the effect module. The same applies for a "kind of verb".
-
You can upgrade directly via USB memory stick. Our current release and public beta revisions are available on our download page. Instructions are included in the package. You can upgrade in one step from 5.1.0
-
Ok, and what is wrong with the scenario on the picture?
The buttons of B, C, and D are unlit indicating that those modules are in off-state.
The color LEDs indicate the effect types in those modules. So, there is a flanger or phaser in module B waiting to get activated. That is the idea.
-
Forgive me as I'm very new to this.
When I crank up the mix on Ionosphere Reverb presets to 100% wet, the overall signal volume increases drastically. My DLY+REV is set to 0%. Is there a way to counteract this? A volume parameter/setting would cover this neatly.
I cannot reproduce such behavior. Between 0% and 100% you dial the wet portion of the signal. Beyond 100% the wet portion stays flat at maximum and the dry signal portion is decreasing. The overall signal doesn't increase. As intended.
-
The color LEDs stay always on in order to indicate the effect type, even if the module is switched off.
-
Have you considered two PROFILERs set up as clones and connected via MIDI ("UI to MIDI")?
-
I guess, I don't exactly understand your intended setup.
If you deactivate and lock the Stack Section the Output Source "Stack" would practically just include the modules A-D.
If you configure Loop Mono into module D and activate that effect loop, the SEND would deliver a signal including Module A-C.
-
CC# 11 controls the Morphing Pedal.
OS 7.0 will introduce CC# 36 to control the Morph Button including the mechanics of Rise Time and Fall Time.
-
You simply connect the 100 Watt cabinet to the SPEAKER OUTPUT of the PROFILER. Even at loud volumes you will hardly exceed 15 Watt. To burn your speakers you would need to run at insane volumes over a long period.
-
Then the FCB 1010 is broken,I guess. I know, these pedals work with a LED light barrier and a foil stripe. The foil stripe is connected to the pedal and is moving through the light barrier while you move the pedal. It works like a continuous shutter. Perhaps there is a mechanical issue inside the FCB 1010, that could be fixed.
-
Your question is very unspecific and terminology is unclear.
I guess, you don't intend to "automate MIDI channel switching". You do this once and keep the MIDI channel setting. By default the receiving MIDI channel is set to "Omni". You can leave it there.
Assuming that you intend to load Rigs in Browser Mode (or Slots in Performance Mode?), you need to send MIDI program changes. If the PROFILER receives a MIDI program change it displays a "'#" for a short moment. If this program change number is assigned to one of the Rigs in your Browse Pool, the PROFILER loads that Rig. The assignments are managed on page "Browse Mode OrgChg" in System Settings. Details are in the Main Manual.
-
This calibration of the built-in pedal is really a job that has to be done within the FCB 1010. And that is the purpose of the FCB 1010 pedal calibration.
If your pedal sends MIDI control change #7 value 15 as the lowest, the PROFILER cannot interpret this as value 0.
-
Wouldn't the practical approach in such a scenario be to change the tuning in the recording software?
-
Agree to paults. As long as the preset is current it can be figured out the way he is suggesting.
However, most of the situations people want to refer to the "current preset", there is no such thing! We don't want to indicate something as "current preset" which doesn't exist. There might be a preset which had been loaded in the past followed by parameters changes. So the current state is not equal to that preset, might not even be close, could be completely different.
-
The volume parameter needs to sit within a module, that can be locked. It would work with any effect that has a volume control.
-
Not through Morph I don't think so...the point is Morph is set up specifically per slot so almost by definition is not globally set...
As I suggested above … by locking the modules these become global including the morphed parameters inside.
Example:
Place a Pure Boost in module X and a Delay in DLY module.
Set the volume of the Pure Boost and the Mix of the Delay up for morphing.
Lock the two modules X and DLY.
Now you can load any Slot/Rig. The Pure Boost and Delay are maintained. And you can morph the parameters at any time.
-
You could use a booster effect and a delay effect and lock those two modules.
-
just love the new reverbs
Is there a way to copy a performance to a new slot and maintain the current setting and not going back to the zero settings for stomps etc. What I am getting at is when you tweek the parameters of a performance like wah, gain, any settings within a stomp , volume etc and come to an amazing sound that you would like to keep as is , if you copy it and then paste it into a new slot , then the new slot when you click on it will revert back to the un tweeked original sound of the performance. So is there any way to take a snapshot that will take with it the exact parameters you have tweeked.
regards Robbymust
You can copy the current edited Slot (COPY button), navigate to another Slot, and paste it there (PASTE button). However, if you hit the Rig Buttons of the Remote to load Slots, former edits to the Rigs will get withdrawn. So, either you store the Performance before you change Slots via Remote OR you stick to the RIG Navigation Cross on the front panel to navigate to other Slots.
