Posts by Sledge139

+1

Here is a sample using TriAxis L2 Red and Triaxis L2 Green 3m, Each side has both profiles.
No EQ or anything except a limiter on the output track.
Not sure who made the excellent DI tracks, would give them credit if I knew.

https://soundcloud.com/sledge1…per-triaxis-profiles-test

Quote from DrBertson

Here is the schematic I based my Mark V pedal on, is the schematic of a Mark IV, but after some tweaking of the schematic, compared with Mark V schematic and a Booster circuit before the Mark IV circuit, I got the right sound.

Quote from DrBertson

http://www.sabrotone.com/?p=814

Thanks for the link!

Thanks a lot for this! Worked pretty dam good!

I really like the sound of these Mark V pedal - simulator profiles. Did you make this pedal and sim yourself? Would like to know more about these. And if there is a DIY schematic floating around?

Really like these profiles. Thanks and good job!

How are you configuring the Q for all of these? I can only set the Q for the 2 mids in the studio EQ.

Thanks for this, I love the Mesa EQ. I need to test this with my Triaxis instead of using dynamic voice, when making new profiles.

Thanks guys for trying them out.

I made a couple more profiles last night. Had some strange issues with my Kemper last night everything was clipping even ones I've used before without issue, so I changed my input, reamp sense and SPDIF settings.

I'm thinking I'm making profiles too hot so I will lower the return level a bit and make them more universally useable.
I'm only running my Kemper to studio monitors so I have no idea what they will sound like through a powered FRFR setup.

Anyone having to turn these profiles down due to clipping?

I'll upload more once I figure out which ones are worthy and what level they should be at.

Thanks guys. I'm open to suggestions. The first few profiles I did pretty quick for a test. They work great with my EMG pickups. I tested with another guitar with a SD distortion pickup and it was a bit mushy sounding. So I will probably do some that works better for that guitar.

Djemass do you have any requests?
I could try some lead 2 yellows to see how it compares to your awesome IIC profiles.
I'm very rusty with the Triaxis so I'll see if I can find some settings online.

BTW my attempts at Lead 1 Red (Recto) have been a failure so far. I need to read the Triaxis manual, I remember liking the mode in the past through my amp. It's either the record out or my feeble attempts to get the tone I'm looking for.
My go to mode was always Lead 2 Red (Mark III)

In case anyone is wondering...
The difference between the Triaxis and the Quad is the Triaxis sounds slightly compressed and the Quad pre sounds more alive and amp like to me.
When set up right they both sound awesome. I've just had an easier time getting my tone dialed with the Quad.

One day I'll work on getting some Quad profiles. I was discouraged early on when I couldn't get DI profiles to sound anywhere as good
as the real preamp and gave up on replacing it in my rack with the Kemper. Even with the multitude of preamp profiles available, nothing I've found has the same magic.

Thanks Djemass!
I was surprised as I haven't used the Triaxis in years due to it not sounding as good as the Quad in my rack.
Was blown away by the record out tone. In your face sound, without the phase issues I hear in many other profiles.

The kemper did a good job profiling it, there is a slight bit of magic lost but it still sounds good to me.
Had to adjust the amp stack on the profiles to get the tone to have the beef I'm used to.

I've started profiling the other modes. If there is more interest I'll share some more.

Pulled out my old Mesa TriAxis and created a few metal profiles using the record out. After all these years, I'm surprised I never tried the record out before, sounded better than expected!
Anyways they are up on the rig exchange, have fun.
find them under Kyle Stevenson

Here is a sample mix using TriAxis L2 Red and TriAxis L2 Green 3m
https://soundcloud.com/sledge1…per-triaxis-profiles-test

There are some good tones in your profiles. Thanks for sharing!

I've heard that you can send your firepod in, and they can put an older firmware on it. I've just gotten used to the Mexican hat dance to get it working. It's a pain but keeps me from throwing out a decent interface.

Quote from Thumas

I bought the microphone locally a few years ago, don't know if you still can buy them.
nr 4 is probably my favorite to.
Here are the settings.
http://www.chain-metal.nl/mark…5&g2=60&g3=15&g4=50&g5=60
Classic mark settings

Thanks man! I'll try it out.

Glad to hear everything's good.
I just tried the new profiles and love them, especially 57 copy 4!
Do you have a link to where you bought the mic? I'd like to check it out.

Also if you don't mind taking the time, I'm curious of your Mark III settings. I wonder if it would sound close dialed on my Quad.
In case you don't have it, a link to the Mark III settings tool. http://www.chain-metal.nl/mark3/
Thanks again.

Thank you for sharing the profiles. I haven't had a chance to test them yet. Hope everything is ok and the removal of all your gear is temporary.

It annoys me as well. Nobody has time for that.

Quote from db9091

But I'm not waiting for the Kemper Team to get on this. I am impatient. I'm buying a Purple Jewel from Amazon for $7 bucks and gluing that shit on.

That's some funny shit right there.

My live setup is a Mesa Quad into a Strategy 500 and with the Thumas and Djemass profiles I feel right at home.
Your other profiles are great as well. I just hope I haven't missed any. Keep up the good work! Thanks again.