Der Wert ist global sobald du die Funktion Lock Vol Pedal aktivierst. Ansonsten kannst du für jedes Rig einen eigenen Wert einstellen. Das gilt auch für die Position des Volumenpedals.
Posts by Kemper Support #1
-
-
Sobald du das Pedal bewegst sollte es den Wah-Effekt kontrollieren.
Die Stomp muss natürlich aktiviert sein.
Außerdem muss CC7 auf dem richtigen MIDI Kanal zum Profiler geschickt werden.
Ob da was ankommt kannst du im System Menu sehen -
Die einfachste Lösung ist es nu ein Pedal zu verwenden und die Volume to Wah Option Im Profiler zu aktivieren. In Rigs in denen ein Wah Effect einem Stompslot zugewiesen wurde wird dabei automatisch aus dem Volumenpedal ein Wah Pedal.
-
Du kannst die globalen Settings im System Menu wieder herstellen, in dem du die entsprechende Funktion ausführst.
Eventuell hast du die Pedal Range für das Volumenpedal verstellt. Diese Funktion findest du im RIg Menu.
Werkseitig steht der Wert auf -5.
Wenn Volume Pedal to Wah angewählt ist dann funktioniert das Pedal in Rigs die einen Wah Effekt verwenden nicht als Volumenpedal sondern als Wah Pedal. -
Some things I've noticed:
1) Stepping on a button A-D does not seem to deactivate other active buttons. This could make it necessary to tap dance in some situations. On my current board, I can step on a switch, it will send a CC command to activate the desired FX, while the other active stomps will be sent a 0 message to deactivate.The Remote can do this easily. Simply assign one stomp in its bypassed state and the other one in its active state to the same switch-instant toggling!
-
Probably the time zone thing
-
To be fair the ticket came in on saturday and i answered it on monday when i got back to work.
-
Das ist mit Absicht so. Eine hell leuchtender Taster zeigt an, dass eine Funktion aktiv ist. Ein nichtleuchtender Taster zeigt das Gegenteil an. Halbleuchtende Taster zeigen an, dass eine Funktion verwendet werden kann z.B. EXITt oder PAGE
-
When you get a problem with buzz and hum please use the Groundlift buttons on the back of the Profiler.
-
We updated the announcement to a Q1 release.
-
in my quote i was talking about using the analog outs. For SPDIF the OP is right-there is no option available for GIT/Master Mono
-
make sure to select master mono as the output source for the main outs if you only use one cable there because otherwise you will loose one half of the stereo signal for rigs that use stereo effects like chorus, stereo widener, stereo delays and reverb.
-
Sure-simply use the main outs for monitoring in stereo including all the effects and assign stack as the output source to either the monitor or the direct out to record a mono track in an analog fashion.
-
the power supply in the Profiler has a security circuit that will shut down the Profiler before voltage problems could do any harm to any of the internal components. There is no way that bad voltage could influence the sound quality in the Profiler-i confirmed this with our chief hardware designer!
-
Die Remote ist auf den Performance Mode zugeschnitten.
-
The Profiler does NOT change its sound due to voltage problems. It is a digital device.
-
Glad you fixed it. Must have been the patch cables for sure because like every digital device changing the power cable wouldnt make a difference. The Profiler either gets proper voltage and runs or it gets no voltage and doesnt run.
-
Der Kopfhörerausgang hat keinen eigenen EQ.
-
Rig switching will be greatly improved in the upcoming 3.0 firmware. You can find more info about it in the news section of our website.
-
Der Rate Reducer gehört zur Gruppe der sogenannten LOFI-Effekte und verringert die Sampling Rate des Klangs. Dadurch entstehen Aliasing Artefakte, die in einigen Stilrichtungen durchaus gerne verwendet werden (Dubstep,Numetal etc)
Quasi eine gewollte Verschlechterung des Klangs. Muss man nicht gut finden, kann man aber.