So I was playing my Player when suddenly there was no sound anymore. I looked at the device and half of the leds were blinking red.
There was another thread here about this and suspicion was voltage issue.
I have a CIOS Sol with 4 ports used for the Player. It was set to 12v / 400ma.
I now changed it to 9v/600ma per port.
It’s weird because i’ve been using it with the 12v ports for weeks now at my place.
Did Kemper ship you the screen?
No worries, thanks for making it available again! 🤘
How do you use the Dunlop? More as a volume, or as a wah?
Exclusively as a wah
Got the Sol + grip + cables today. Just need to get another flat cable to replace the green One and it’s
Done.
Currently doing that (4. outputs into one) works fine
Do you set the outputs to 9v or 12v?
Aaah gone already?
Has anyone tried to use the Cioks SOL with current doubler cables to power the Kemper?
I ordered the Sol, should arrive tomorrow hopefully.
I have a dunlop mini x connected to the exp input on the player. When i have a rig with a wah, everything works as it should.
However: when I switch to a rig that has a volume pedal everything works great within that rig. The following issue occurs after using the expression pedal as a volume and switching back to a rig with a wah slot: gain is gone. All profiles now sound like the gain has been turned down 80%.
Sometimes, when I unplug the cable in the expression input, the sound is gone completely. Reinserting the exp cable brings back the crippled gain sound.
Only solution is to power cycle the Player.
I used my Moog EP-3 from my power rack, and same issue.
ah crap, yeah. So then I would need 3 of those 8800 cables? 2 cables for the 4 outputs, and 1 cable to combine to other two cables.
Would I still need to set the outputs to 9V then (combined 2,64A) or 12V (combined 2A)
I'm about to get a Ciosk Sol, as that should also work to power the Player + my Shure GLXD16 wireless pedal, and is a heap cheaper than the DC7 + Crux
I would need the Cioks 8800 cable to combine two 9V ports, correct?
Exactly this!!!
You’ll need to ship it to kemper hq then
Maybe they’ll release a small display for the
Tuner that connects to the usb port 😂
Hey! could you add a couple more pictures of your board by any chance? I thought the metro 16 was bigger..but it looks good. Initally I was planning on getting the voodoo labs dingbat tiny.
Sure. Here it is with the dunlop dvp4 instead of the “big” kh-95 wah.
I had something similar happen a couple of years ago.
Does it sound like this (notice that nothing is connected to the Kemper): Video.MOV
It's a hardware issue and some things need to be replaced. In my case it was an ICM board and analog board plus an internal ribbon cable that were replaced under warranty (I had 1 week warranty left luckily)
Allow me a stupid question:
How do you guys attach the Player to your boards? A little velcro tape on the corners?
I used the velcro that came with the Metro16 and taped it in the corners and on some other parts while trying to avoid covering the middle vent and the qr code.
But by doing that it’s not really fixed very tight and a bit wobbly. It won’t fall off unless you hold the board upside down and shake it 😅
That said 3M dual lock is the better choice as tsachou already said
It does! Tried it…it’s protruding a bit unfortunately. Looks like the Metro 16 is a better fit.
Tadaaaaa! The KH-95 will be replaced with a Dunlop mini dvp4 as the KH is a bit too big for the Metro16.
The vent at the bottom of the player is pretty much obstructed by the metro16’s middle beam.
Hope that won’t cause issues.
I’ve seen some people in the Quad Cortex community run their QC from powerbanks.
Anyone already tried this with the player?
And another thing.... how would you achieve dual amp setup with the Player + Power rack?
I assume that I would plug my guitar into the power rack and would use direct out (set to Git) --> to input Player. XLR on both devices would go to FOH.
If I would want to monitor the dual amp setup via headphones (at home for instance, or IEM setup), I assume that the main out (TS) on the Player would then need to be connected to the alternate input on the Power rack, so I can set the mix?
Would that be correct?
