Posts by marianguitar

Quote from Wheresthedug

a combination of panorama and the stereo control within the harmoniser should do it no problem.

Somehow I didn't figure it out. I can ask how to set the Rig so that I get the whole (complete) signal to the right, with the harmonizer in the chain of effects. just everything i use (effects) everything i want to end at the end (effect and dry signal) on the right side, thanks ...

* * *

Nejako som na to nedošiel. Môžem poprosiť, ako nastaviť Rig tak, aby som celý (komplet celý) signál dostal do pravej strany, s tým, že v reťazci efektov je aj harmonizér. proste všetko, čo použijem (efekty) všetko chcem aby skončilo na konci (efekt a dry signál) na pravej strane, díky...

I haven't read it somewhere or it doesn't work, so my question is: Is it possible to adjust the whole sound to one side with the intelligent harmonizer? (ie either left or right as needed but also with DRY signal, complete everything ???

* * *

Nejko som sa tam nedočítal alebo to nejde, takže Moja otázka znie: Je možné pri inteligentnom harmonizéry nastaviť celý zvuk na jednu stranu? (tj buď vľavo alebo vpravo podľa potreby ale aj s DRY signálom, komplet všetko???

Quote from Wheresthedug

try page 183 of the manual under the heading Stereo

There is not even a page on the Kemper page when I download the 7.5 manual page 183. it ends on page 164

* * *

Na stranke Kemper ked stiahnem 7,5 manuál strana 183 ani nie je. končí to stranou 164

no one can advise?

OK, I HAD IT, THE PROBLEM WAS ELSE. I also use the GR-55 guitar synth and there was a panorama in the middle But now a nut. I use an intelligent harmonizer in some parts of the song and it also needs to get to one side of the signal and I still can't do it! The original is ok but the other voice goes to the opposite side of the signal. How to get it all on one side? Specifically, it needs to get to the left - a complete sound dry + harmonized.

* * *

OK, ZVLÁDOL SOM TO, PROBLÉM BOL INDE. Použvam aj GR-55 guitar synth a tam bol panoráma na stred

Ale teraz oriešok. V niekotrých častiach skladby používam inteligentný harmonizér a ten tiež potrebuje dostať do jednej strany signálu a stále sa mi to nedarí! Originál je ok ale ten druhý hlas mi ide do opačnej strany signálu. Ako to dostať všetko na jednu stranu? Mne konkrétne to treba dostať doľava - komplet zvuk dry + harmonizovaný.

ok, thanks

Quote from Burkhard

You could use the parameter Panorama and set it either completely to the left or to the right.

I own a Kemper Profiler Stage. The manual I got for it in our language somehow doesn't contain anything about the "Panorama" effect.Where specifically (in which module is it located? Thanks.

* * *

Ja vlastním Kemper Profiler Stage. Ten manuál, čo som k tomu v našom jazyku dostal, nejak neobshuje nič okolo efektu "Panorama".

Kde konkrétne (v ktorom module sa nachádza? Díky.

Hi, I have a question: I would like to use a mono signal on Kemper for output for some reason, directed (according to my need) either to the right or to the left. How to achieve this.

Note: I will need to point to the right (guitar) for some rigs and to the left (ukulele) for some rigs.

thank you for advice.

* * *

Ahoj, Mám otázku: Chcel by som z určitých dôvodov používať na Kemper na výstupe mono signál, smerovaný (podľa mojej potreby) buď vpravo alebo vľavo. Ako toto dosiahnúť.

Poznámka: budem potrebovať pre niektoré rigy smerovanie vpravo (gitara) a pre niektoré rigy vľavo (ukulele)

ďakujem za rady.

MIDI problem

In the Pedalboard, I have three devices connected via MIDI: Kemper Profiler Stage, Roland GR-55 guitar synth, and these two devices are controlled by the MIDI pedal Microdesignum MIDI Forte 16F2D.

MIDI connection: from "MIDI Forte" I go with MIDI OUT to "Kemper" to MIDI IN. And from "Kemper" I'm going via MIDI OUT to MIDI IN Roland GR-55. I have MIDI channels agreed, everything works as it should !!!

When I play, every approx. 2 (3) seconds (it is exactly the same interval) I get an audio signal (complete sound, which is in the signal Kemepr or GR-55 or both it doesn't matter) for a short time. When I unplugged the Roland GR-55 midi cable with MIDI IN, it stopped, but what about the fact that I don't have data on the GR-55 (on the Kemper yes)

And one more interesting thing: When on GR-55 (I have a set of MIDI connected as I described it at the beginning) and I go to SYSTEM - MIDI SETTINGS (and I don't do anything there either, I'm just in this section) then the interruption will stop. But when I return to PLAY PATCH mode, it will start to interrupt again. I can't advise where the problem might be ????

Here is a preview of the pedalboard:

[img width=800 height=450]http://mojagitara.com/wp-conte…kemepe-gr55-midiforte.jpg[/img]

I will write a simple example: I need to send for Kemper MIDI Program Change 1 to channels 1 and for Roland GR-55 MIDI Program Change 1 to channels 2. AKo Connect the Devices so that it works. From a MIDi pedal to Kemper and then to the GR-55? Or from the MIDi pedal on the GR-55 and then on the Kemper. But that's not the point. Simply the data sent from the MIDI pedal to the Kemper Program Change switches Kemper but does not reach the GR-55 and vice versa. I don't need anything else, to get the ice on Kemper and GR-55 via MIDI Program Change, it doesn't work for me, I have the channels set up, how to set it up in Kempry so that the PCH data on channels 2 goes to GR-55?

* * *

Problém s MIDI

V Pedalboarde mám zapojené cez MIDI tri zariadenia: Kemper Profiler Stage, Roland GR-55 gitarový synťák a tieto dve zariadenia ovláda MIDI pedál Microdesignum MIDI Forte 16F2D.

MIDI zapojenie: z "MIDI Forte" idem s MIDI OUT na "Kempera" na MIDI IN. A z "Kempera" idem cez MIDI OUT na MIDI IN Roland GR-55. MIDI kanály mám odsúhlasené, všetko funguje ako má ale!!!

Keď hrám, tak každú cca 2 (3) sekundy (je to presne rovnaký interval) mi na kratučkú chvíľku vypadne audio signál (komplet zvuk, či už je v signále Kemper alebo GR-55 alebo oboje to je jedno). Keď som vypojil na Roland GR-55 midikábel s MIDI IN prestalo to, ale čo s toho, že tým pádom nemám data na GR-55 (na Kempery ano)

A ešte jedna zaujímavosť: Keď na GR-55 (mám zapojené komplet MIDI tak ako som to popisoval na začiatku) a prejdem do SYSTEM - NASTAVENIA MIDI (a ani tam nič nerobím, len som v tejto sekci) tak prerušovanie prestane. Ale keď sa vrátim do PLAY PATCH modu, zase to samo začne prerušovať. Neviem poradiť, kde by mohol byť problém????

Tu je náhľad na pedalboard: foto viď vyššie...

Napíšem jednoduchý príklad: Potrebujem poslať pre Kemper MIDI Program Change 1 na kanály 1 a pre Roland GR-55 MIDI Program Change 1 na kanály 2. AKo Zapojiť Zariadenia tak, aby to fungovalo. Z MIDi pedálu na Kemper a potom do GR-55? Alebo z MIDi pedálu na GR-55 a potom na Kemper. Ale o toto nejde. Proste data posielane z MIDI pedálu na Kemper Program Change prepínajú Kemper ale nedostávajú sa na GR-55 a naopak. Nič iné nepotrebujem, led dostať na Kemper a GR-55 cez MIDI Program Change, nefunguje mi to, kanály mám nastavené, ako to nastaviť v Kempry aby data o PCH na kanály 2 prešli do GR-55?

I have a question: is it possible to control the switching between BROWSER and PERFORMANCE mode?

Any MIDI command? Or other than manually pressing the corresponding button?

* * *

Mám dotaz: je možné nožne ovládať prepínanie medzi BROWSER a PERFORMANCE mode?

Nejaký MIDI príkaz? Alebo inak než ručným stlačením príslušného tlačidla?

Quote from Wheresthedug

Pitch pedal works like the Digitech Whammy pedal. Is that what you are looking for?

Yes, I've already figured out how to do it. It is not enough to choose a PEDAL PITCH but it is also necessary to define in the "PEDALS" section one for "PEDAL PITCH". But thanks for the advice

***

Ano, už som zistil ako na to. Ono nestačí si vybrať PEDAL PITCH ale treba aj nadefinovať v sekcii "PEDALS" jeden pre "PEDAL PITCH". Ale díky za radu

Hi, I would like an effect where I can change the pitch through MORPH, for example: the default setting is 0 and in the Expr max. the pedal would be an octave up. The whole thing could be tuned smoothly through the MORPH pedal. Which effect in Kempery can I achieve? Well thank you...

* * *

Ahoj, potreboval by som efekt, kde môžem cez MORPH meniť výšku tónu, napr: základné nastavenie je 0 a v maxime Expr. pedálu by bolo oktáva hore. Celé by to šlo plynule prelaďovať cez MORPH pedal. Ktorým efektom v Kempery to dosielahnem? Ďakujem...

I wanted to ask about this problem: In the new Rig Managers in the OUT section there is the option to set both Main output and monitor output independently. I would like to use it for two independent stereo output (guitar and ukulele) and it occurred to me that how can I set Main OUT to 12 dB and Monitor OUT to - infinity or vice versa, so maybe it should be somehow stored? or?

Simply, I would like the rig used on the guitar to set Main OUT to 12 dB and Monitor OUT to - infinity and rigi ukulele vice versa: Main OUT to - infinity and Monitor OUT to 12 dB.

now it is just whether it can somehow tie to each rig independently ???

http://mojagitara.com/kemper-profiler-out-sekcia/

* * *

Chcel som sa spýtať na tento problém: V novom Rig Managery v OUT sekciije možnosť nastaviť Main output aj monitor output nezávisle. Chcel by som to využiť pre dva nezávislé stereo výstupy (gitara a ukulele) a napadlo ma, že tak ako si viem nastaviť Main OUT na 12 dB a Monitor OUT na - nekonečno alebo naopak, tak by sa to asi malo dať aj nejako uložiť? či?
Jednoducho, chcel by som rigy využívané na gitaru nastaviť Main OUT na 12 dB a Monitor OUT na - nekonečno a pre rigi ukulele naopak: Main OUT na - nekonečno a Monitor OUT na 12 dB. teraz ide len o to, či sa to dá nejako naviazať na každý rig nezávisle???

http://mojagitara.com/kemper-profiler-out-sekcia/

Quote from Burkhard

You could for example place the Transpose effect in Module C and dedicate the Looper button to toggle Module C on and off. To customize the Looper button use the function Button Assignments on page Remote Settings within System Settings.

Thank you for the info, but I know this. My point is that I do not have to occupy any controls I to IIII. and not a switch, this one is designed for HARMONY.

To explain the situation: I have already assigned effects and their positions and if I wanted to use somewhere (for example, for module "C" transposition, I would have to "throw" another effect from there.

* * *

Ďakujem za info, ale toto poznám. Mne ide o to, aby som nemusel obsadzovať žiaden ovládací prvok I. až IIII. a ani switch, ten mám takto určený pre HARMONY.

Aby som vysvetlil situáciu: Už mám zadelené efekty aj ich pozície a ak by som chcel použiť niekde (napríklad na modul "C" transpoze, musel by som "vyhodiť" odtiaľ iný efekt.

My question: Is it possible to define Transposition on any of the foot switches (ideal for me on TAP or LOOPER)? In practice, I would play normally and if necessary, I would just press the appropriate button and the guitar would tune or tune according to the set parameter. I know it is possible to set it not only in pitch but also in rig - transpose, but here I would have to write a new whole sound. this way I could use all the sounds and transpose them as needed.

* * *

Moja otázka: Je možné na niektorý z nožných spínačov (ideálne pre mňa na TAP aleboLOOPER) zadefinovať Transpozíciu? V praxi by som hral normálne a v prípade potreby by som stačil príslušné tlačidlo a gitara by sa podladila alebo nadladila podľa nastaveného parametru. Viem, že je to možné nastaviť nielen efektom "pitch" ale aj v rig - transpose, ale tu by som musel zapísať nový celý zvuk. takto by som mohol využívať všetky zvuky a podľa potreby ich transponovať.

Quote from Burkhard

It's all in that MIDI chapter in the manual.

You can use MIDI control change #47 with a value n to preload a particular Performance n in pending mode. A control change # 50-54 needs to follow to load then one of the five Slots of that Performance.

Or you send a fully qualified address including MIDI bank select LSB plus program change to load any of the 625 Slots in Performance Mode. With that you could jump from Performance 1 Slot 1 to Performance 125 Slot 5, if you want.

It's all in that manual chapter.

Display More

Yes, I've already got it, I write about it

http://mojagitara.com/kps-zmen…performance-modence-mode/

Quote from Burkhard

I might not understand your question. There are no Performances in Browser Mode. You can assign 128 Program Changes to 128 Rigs in your Browse Pool and load these via MIDI. If the assigned MIDI PC# is received, the Rig gets loaded independent of View and Sort by. However, I think Performance Mode is the better choice.

I suggest you read the chapter MIDI in the Main Manual which explains, what can be controlled remotly in Browser Mode and in Performance Mode in great detail.

Yes, I know that, I ask if it is possible to "change" PERFORMANCE in some way, just like the "Performance UP" and "Performance Down" buttons on Kemper Profiler Stage (but these can only be stepped up or down But if there is no way to switch from Performance 1 to Performance 100, for example.

* * *

Ano, to viem, ja sa pýtam, či nie je možné nejako "skokom" meniť PERFORMANCE". Proste tak ako je na Kemper Profiler Stage Tlačidlo "Performance UP" a "Performance Down" (týmito však je možné prechádzať len krokom nahor alebo nadol, alebo ho podržať. Ale či nie je možnosť prepnúť napr. Z Performance 1 na Performance 100.

• A question for MIDI proficient: Is it possible, in Browse mode, to switch rigids using Program Change to switch MIDI reports? The idea: press PC1 to switch 1 performance, press PC32 and switch 32 performance, ie analogously. The prospect would be to switch performances (not rig) and in the performance I have 5 slots - presets.

* * *

• Otazka pre zdatných v MIDI: Dá sa tak ako je v Browse mode prepínanie rigov pomocou Program Change prepínať aj zostavy (performance) cez MIDI? Predstava: stlačím PC1 a prepne sa 1 performance, stlačím PC32 a prepne sa 32 performance, čiže analogicky. Výhada by bola, že prepnem performace (nie rig) a v performance mám k dispozícii 5 slotov - presetov.

I have a request. I use Kemper on a special guitar where one fingerboard is an electric guitar and the other one is a ukulele with a piezzo pickup. Sounds on el. the guitars are cool but I can't create or find a sound that is closest to the acoustic or piezzo electric ukulele sound. if you give me some types where to download and try such sounds, or how to create this best (on which STACK or speaker or directly. Thank you ...

* * *

Mám prosbu. Kemper používam na špeciálnu gitaru, kde jeden hmatník je elektrická gitara a druhý hmatník je ukulele s piezzo snímačom. Zvuky na el. gitaru sú v pohode ale nedarí sa mi vytvoriť, respektive najsť vhodný zvuk, ktorý by bol najbližšie akustickému alebo piezzo elektrickému zvuku ukulele. mrád ak mi dáte nejaké typi, kde si takéto zvuky stiahnuť a vyskúšať, alebo ako toto najlepšie vytvoriiť (na akom STACKu resp. reproboxe, či napriamo. Ďakujem...