Yeah but they aren't really acoustic or bass amps and cabs. They're guitar amps.
Where do you find this wrong information? Which of the Rigs uses a guitar amp?
Yeah but they aren't really acoustic or bass amps and cabs. They're guitar amps.
Where do you find this wrong information? Which of the Rigs uses a guitar amp?
Hallo Tim,
ein Profil bildet das mikrofonierte (!) Gitarren Rig ab. Die Interaktion der Endstufe des Verstärkers mit der Box ist darin enthalten. Dadurch ergibt sich ein sehr natürliches Spielgefühl. Im Blindtest wird kaum ein Gitarrist einen Unterschied bemerken.
Man findet so ziemlich alles an Amps als Profil, was einem in den Sinn kommt. Liquid Profiling erweitert das Profiler Konzept um authentische Tonestacks, die das Profil wie den Amp regelbar machen.
Meiner Meinung nach ist es nur sinnvoll, den analogen Verstärker zu benutzen, wenn der Spieler im Aufnahmeraum bei hoher Lautstärke die sich bewegende Luft braucht. Dann ist aber der Lastwiderstand nicht erforderlich (von einigen Ausnahmen abgesehen). Somit sehe ich einen hybriden Ansatz als wenig zielführend.
Der zeitliche und im Studio damit finanzielle Aufwand kann mit dem Einsatz des Profilers signifikant minimiert werden. Natürlich muss man dann ein Arsenal an Profilen verfügbar haben, das dem vom Künstler oder Produzenten klangmäßig nahekommt.
Die Alternative, ein Direct Amp Profil zu erstellen und mit Cabs aus anderen Profilen zu kombinieren erfordert nur kurzzeitig einen gewissen Lärmpegel. So hat der Gitarrist immerhin den emotionalen Vorteil für sich, denn er spielt mit dem Profiler ja dann „seinen“ Amp.
Yoda Guitar Danke für das Feedback bezüglich des Monitor Outputs. Da sollte das Signal bei eingeschalteter Kine Funktion linear kommen. Das prüfe ich mal.
Ich beziehe mich auf die Mac Systemsteuerung für digitales Audio, nicht auf spezifische Software wie bei Focusrite.
The Profiler Player comes loaded with Acoustic Rigs in Bank 9 and Bass Rigs in Bank 10.
As advised already, please open a support ticket.
I have the same problem player will not connect to IOS rig manager via wifi
Please open a support ticket.
Dynochrome This marks the maximum Output wattage for the Kemper Kabinet with a powered Profiler or the Power Kabinet connected to the Monitor Output. Users should not exceed their volume settings to avoid damage to the Kone speakers that can handle 200 Watts.
Yoda Guitar Ich kann es bei mir nicht nachstellen. Die Output LED wird bei mir zwar rot, aber das abgespielte Material vom Rechner ist völlig intakt. Es gibt in der Mac Systemsteuerung keine Lautstärkeregler für digitale Verbindungen. Ist für mein Focusrite Interface auch nicht verfügbar.
Ein Video hilft. Welcher Wert ist für DAW Volume eingestellt?
theplayer If you answered my questions we might find the solution.
theplayer What I am asking is: Which Output Source is set for the Monitor Output and the Direct Output?
Are you using an expression pedal?
Yoda Guitar Ist das ankommende Audio am Profiler tatsächlich verzerrt?
theplayer What is your set up exactly? What is set for the Outputs you used?
Does the Input LED light up when you play the guitar?
I use a very long USB cable as a repeater solution does not work with the toaster or the rack (I tried to connect over WLAN). With the long cable, it works really well.
When using a WLAN repeater the Profiler will only connect to Rig Manager mobile apps on iOS or Android. Rig Manager works via USB only.
warretaliator Please Open a support ticket.
hcornea Please Open a support ticket.
DonPetersen Beat me to it!
theplayer The Dani California solo reminds me of Purple Haze. I get pretty close with the TD - Jim Hen Rig from the Kemper Legends Tribute Col. 1-3 Rig Pack. Turn on the Octa Shaper and Phaser Vibe, on a neck single coil (I am using a Tele) with the treble rolled down.
hcornea Please check in your iPhone settings for Rig Manager if the Mobile Data option is set to on. If so, turn it off.
InfiniteSustain Please open a support ticket.