Posts by Jevo

Yes ST, it work that way perfectly! Thanks!

And the best thing is that I can reamp a recorded solo through spdif and play with the expression pedal so if I dont like my wah performance do it again without having to record the solo again.

Oh my God! Epic fail. User since 2013 and I didnt know there was a dedicated input for pedals in the back!

I never used wahs or expresion pedals in my life, I'm totally noob on that. I watched a video in Youtube and it seems to connect to the front input.

My apoligizes for my stupid question and thank you very much!!

I got a Dunlop (X) Mini Pedal and I cant make it works.

Guitar (TS)->Pedal(TRS)->Kemper Input, then activate Wah stomp but it doesnt sound.

What am I doing wrong? All tutorials make reference to Remote. Is it necesary to have the Remote or what?

After some years releasing free profiles I've created a pack called "Lord Of The Rigs", where you can find profiles from cleans of Rivendel to higains of Mordor.

Get them here:
http://www.elrenorenardo.com/jevo/

INCLUDES
55 Profiles from Clean to Hi Gain. (Check List)
Amps: ENGL Savage 120 & 60, EVH 5153 100W, Engl Blackmore, Marshall JCM2000 TLS

Cabs: Engl Pro 4x12, Engl Pro 2x12, Mesa 2x12
Plus:
+ Old free packs (193 profiles)
+ Previously unreleased profiles for Metal (most EVH5153)
+ Clean profile with FX (you can copypaste this FX preset to any other clean profile)
+ Solo profile with FX (you can copypaste this FX preset to any other profile)

Videos:

Some profiles in a mix. (metal): https://youtu.be/kGJE4XCnzUQ

Walkthrough of some profiles: https://youtu.be/wn4ncozzMIk

Stereo raw samples: https://youtu.be/VGceE8EEfm4

My stolen KEMPER is been found!!

In february my Kemper rack was stolen from the trunk of my car.

I went to police for a report and I also sent an email to Kemper Support so they could include that unit serisl number in the blacklist.

On monday, 4 months later, I got a message from Kemper Support telling me that another user has registered my stolen kemper, and advised me to go back to police and tell them to contact Kemper to give them the IP address.

24 hours later, police told me they had the Kemper back!!

Thanks to Kemper Support for their good work!!

Thanks guys.

And thanks Kemper for the support they give. In case someone tries to registed my device Kemper will send me an email so I can contact police.

I will have to buy another unit. Life without Kemper is not easy

Thanks guys, I will send serial number to Kemper. Police reporte filled yesterday.

I'm going to be aware to pawn shops, second hand online, ebay....

Some fucking bastard stole it from the trunk of my car. The car was not forced so I probably didnt close the car properly.

I've had it since 2013 and I'm very upset and angry. I only wish that shitfaced thief dies slowly in pain.

That's all I wanted to say

Thanks Ingolf, but as you can hear in the clip, it is the same rig, totally clean, which sounds clean with some guitars and fistorted with other guitars.
No RED input light.

I met another guy who has that same issue with some pasive guitars.

I noticed long time ago that I can't get clean tones with some guitars. It is always a little distortion, even with ultraclean tones.
Curiosly, active pickups (Emg, Blackouts) sound totally clean but pasives (SH6, Nazgul) sound distorted. Weird.

Listen to this clip, first part is Blackout (active), second part is Nazgul (pasive).

https://drive.google.com/open?…LVkP3rqxfJS6CMmnrrN_jBCVd

Well, I used the bridge mode with my 4x12, but I decided to go just 1 channel with my 2x12 for having less power. I'm running 1 channel of the setereo (500w)...150w at 16ohm I guess.
Running in Bridge Mode is probably too much (1000W, or 650 at 16 Ohm)

I purchased a 2x12 (16 ohm) cab to play with my Kemper.
Matrix GT1000 has 1000w at 8 Ohm and 650 Watts (at 16 ohm) coming out and the cab only 120 wats (2x V30 speakers) when Briged Mode selected.
I rehearsed yesterday with the Matrix full volume (1 channel 500 watts, not bridged) and Kemper at -10db and still it was not loud enough....but the lights in the Matrix were constantly blinking (that means that 25% of the full power was coming out from the Matrix.
25% of 500 is 125 Watts, which is a bit more than the cabinet can handle.
But specs, say this:
TECHNICAL SPECIFICATIONSNumber of channels- 2
Watts per channel rms @ 4 ohms- 500Watts per channel
rms @ 8 ohms- 325Watts per channel
rms @ 16 ohms- 150 W (is this all I got????)

Video of the lights blinking all the time
https://photos.google.com/phot…6fDAYLwC-KorNR9KMZ0hNH2pi

Are these profiles merged or captured from direct output?

A bit dark, but with tweak to your taste and youll get nice tones.
They have no post edition, just as theywere captured.

AMP: DIEZEL EINSTEIN 50 WATTS
9 setups, from clean to hi gains
2 cabinets (Engl Pro Straight, Mesa Rectifier)
.......................TOTAL 18 profiles .............................
Mic: SM57
Merged Profiles, directly from output of the head. You can combine them with other cabs.
Download them here:
http://www.elrenorenardo.com/jevo/

It uses on stage most of the time (he said in an interview)
Would be nice if someone could sneak to stage with a pendrive and do a backup, hahaha

Hi guys, some weeks ago we had some attack to the hosting (which has 3 sites), but now it seems to be solved...it was some relinks to porn sites. The thecnician told me that everything is ok now and it is installed an Antivirus and AntiMalware plugin in Wordpress. The site even passed Google controls and we have been informed by Google that there is no more links to oher sites nor malware.
I have checked the ZIP myslef with AVAST and they seem to be free from viruses

Cheers

PD: I hope I can create soon some merged profiles of Triaxis, Engl SE and also Sansamp for bass

Merged profiles from one of ENGLs best amps.

8 setups (Clean, Crunch 1, Crunch 2, MidGain 1, MidGain 2, HighGain1, HighGain 2, HighGain 3)

3 cabinets (Engl Pro Slant, Engl Pro Straight, Mesa rectifier)

…………………..TOTAL 24 profiles ………………………..

Mic: SM57

You can download them here:
http://www.elrenorenardo.com/jevo/

Video demo:

Quote from Kempermaniac

Not sure but I recently read about an issue with the internal battery and a loose DSP chip or motherboard. Did you check this? Or maybe you can find the threads about these issues...

mmh... interesting. I also thought abut the lithium battery. Will open the unit and see what I find inside...maybe a racoon ate some cables.

I'm still suffering this issue. Sometimes it is slower, sometimes faster even up to 5 second until it responses. I did all the reinit, upgrades, downgrades...

THERE is a curious fact: When the kemper is being feeded, reamping or playing guitar (Input led green), it works perfectly.
I dont know if sending it to repair due to shipping costs and keep it this way. It is kinda annoying but not a matter of life or death.

Any feedback on sending the kemper to support?
Anyone experimenting this issue?

PD: I forgot to mention, sometimes when turning on the unit, it says somethink like: "hardware issue, contact support"

I made new profiles from my Engl Savage before it is sold.
This time they are 3.0 merged profiles. Amp has been profiles from the speaker output.

CONTENT:

5 Settings (Clean, Crunch, Rock, Metal, HiGain)
3 Cabinet (Engl Pro Speaker, Engl Pro Speaker 4, Mesa OS)
Total ……………. 15 profiles

FREE DOWNLOAD HERE
http://www.elrenorenardo.com/jevo/

Enjoy them