Posts by BRUCEHEARN

When your interface is 48 do you need to change ir to 48?

Sorry for the silly question

Sometimes my interface changes to 48 and the Kemper sounds a bit harsh

Thanks

Thanks. How does the lock work on stomps? So all stomps have their original value for each rig

Its seem that all my profiles are set to post eq and all my studio eq stomp is the same for all profile even though I change to different profile but did save one with other stomps effects

will there be any ir for bass amps?

Just curious and suggestion to get his tone on Walking on the moon and other songs

Thanks

Cheers

Where to adjust the instruments from guitar bass and acoustic?

Thanks

Thanks I have been using spdif sounds better than mains out.

What is the best way to recording KEMPER with Pro tool? Straight from mains out or spdif and do you run it into a direct box? I am using presonus firestudio project
Thanks

Thanks will try it out

is there any way to make my electric 6 string sound like a 12 string on the KEMPER?

just one from the main out either the interface or mackie but not at the same time

I am trying to run the main out set main .mono out to interface FIRESTUDIO AND ALSO MACKIE BIG KNOB but both sound out of phase or hollow put when i use headphone of the KEMPER SOUNDS great.On the cables I use are regular ts 1/4 or xlr.I use the monitor speaker out to Marshall cab and sounds fine,Just the Main out sounds hollow either going to interface or mackie big knob.I have set the lacency on the KEMPER.Is this a routing problem? Thanks Bruce

Thank-you very much! It work with the wah set and not use it now volume and whammy all work.
Thanks again

Quote from hjscheffler

you must configure the pedal as a wah pedal and then activate the pedal links options.
Here is an expert from the reference manual about this
The one pedal then needs to be set-up as a Wah pedal. The PEDAL 5 socket is already prepared for it by default.How to connect and calibrate has been already explained in the example Four Pedals: Luxury. Then select“WahPedal >Volume” and “WahPedal >Pitch” on the Pedal Links page in System Settings.
If “WahPedal >Volume” is selected, those two functions are mutually exclusive. As soon as a Wah effect is active,the Wah Pedal controls this Wah effect, while volume stays flat. As soon as there is no Wah effect in the current Rig,or the Wah effect is switched off, the Wah Pedal controls volume. All other pedal links allow you to control theireffects simultaneously. So, a Morph Pedal could morph and control Wah, as well as pedal pitch effects at the sametime, if those links are selected. And a Wah Pedal could control Wah and pedal pitch effects together, if “WahPedal>Pitch” is checked.
There is also a tutorial video on our website that describes this procedure.

Thanks -I understand this but Just want to use the pitch and volume In system Pedal links you have wah/volume,wah/pitch,morph/wah,morph/pitch no volume/pitch
if i just set pedal6 to pitch works fine or pedal 5 to input 1 pedal 6 input 2 it turns off on the pitch but no volume control or won't calibrate for volume only for pitch
i set the volume after affects in rig -So does this means I need 2 kp1? Thanks

i have the kemper remote and mission kp1 and want to control the pitch whammy and volume after effects Not using wha have a separate device

Thank you everyone for your help.Greatly appreciated Now I get it!
Cheers

How would you setup one going to the board with cab on and one to my 4/12 cab?with cab sim off? and have volume at the same level with the band on stage?

I thought the the monitor out has the same volume as the speaker out. i just got it yesterday.i want to run my 4/12 cab with monitor out and the main out to the board but the monitor out goes to my 4/12 does not come close to speaker out to the cab

THE MONITOR VOLUME IS LOW WITH NO HEAD ROOM CAPare to speaker out