Ja, habe jetzt mal danach gesucht.
Eigentlich schlimm, dass so viele Leute Probleme damit haben.
Wirft kein gutes Licht auf den Kemper.
Aber es kann ja nicht alles perfekt sein.
Ja, habe jetzt mal danach gesucht.
Eigentlich schlimm, dass so viele Leute Probleme damit haben.
Wirft kein gutes Licht auf den Kemper.
Aber es kann ja nicht alles perfekt sein.
Nun denn, ich schaue es mir bei mir auch mal genauer an.
Ärgerlich, dass bei einem Gerät für so viel Geld solche „billigen“ Kleinteile Ärger machen.
Hat sonst vielleicht irgendjemand Erfahrungen mit diesem Fehler?
Oder muss die Remote vielleicht sogar eingeschickt und repariert werden?
Habe das gleiche Problem. Wenn ich ein paar mal am KPA ein und ausstecke, geht es.
Das mit der Feder werde ich mir mal ansehen.
Kannst Du bitte berichten, wenn Du Dir das mit der Feder angesehen hast?
Ab und zu habe ich folgenden Fehler bzw. folgende Störung bei der Remote:
Ich schalte den Kemper ein, Performance Mode.
Der Kemper startet normal und lässt sich auch normal bedienen. Klang ist ebenfalls normal.
Die Remote allerdings startet und bleibt dann in dem Status wie auf dem Bild, wobei wie auf dem Bild
zu sehen ist, ein Lämpchen rot blinkt.
Wenn ich nun das Verbindungskable (Kemper - Remote) an der Remote löse und wieder einstecke
startet die Remote von vorne und funktioniert dann normal.
Kennt sich jemand damit aus?
Wow, it seems amazing that you need to run the Clean Sens and/or Rig Volume so high to get it to a usable volume. That looks like something that might need improved in the actual AS effect itself.
I usually have the Clean sense at about -4.
Not sure if the new setting is the way it‘s supposed to.
Set your Clean Sense (mine is +10dB) and Rig Volume (mine is +8dB). I've unlocked my INPUT section so that clean sense can be different between rigs. This balances it out perfectly in my case, so I'm sure it will work for you also. You could do to +12dB on the rig volume, but that doesn't leave any digital trim (gain) for the pure boost or EQ volume, and increasing those will have no further effect. I left Rig Volume at +8dB to permit a few dB of boost for solos or chorus sections.
Thanks for your answer. Will try different Clean sense settings.
Display Morewhippinpost91850 IngoRockt TobiBorn Serendipity and others...
Just posted my profiles on Rig Exchange. The 'EA Single Coil Acoustic Sim' is the one I've used for the Tele in the more recent video I posted. I've also done a version for those with humbuckers (you'll see it) and no coil tap that works for my Eggle at least and prsgary 's
GibsonPRS. I'll restate the important bits:
- Do not turn on the stack
- Do NOT turn on the stack
- DO NOT TURN ON THE STACK
- Check your Clean Sense and Rig Volume
You need the AcSim and Studio EQ as a bare minimum for these rigs to work. They're in blocks A and B so check those two at least are not locked when you load the profile. I've thrown in some settings I use for compression, a clean boost with delay, the stereo widener, a subtle chorus and Legacy Reverb. If it wasn't clear earlier, don't turn on the stack.
Hope these help some people out!
All the best,
Ed
Thanks for your rigs.
I tried the Single Coil one, but have the problem that the rig is extrem quiet/silent. I tried
some Equalizer to increase the volume but comparing it with all my other rigs, it‘s not usable.
Do you have any ideas?
Should give you a single coil sound. Why not give it a try?
Have the fear that this will sound to thin.
Will try tomorrow.
Unless you can split the humbuckers, it's unlikely to sound close to an acoustic. This sim works best with single coil pickups like on a Strat.
I can split the neck humbucker.
Does this help?
Maybe this question is wrong here,
but could somebody post the settings for a Gibson Les Paul Standard if I want to use the
acoustic simulator?
Upps, gar nicht mitbekommen, dass es zu 7.5 ein neues Handbuch gibt.
Merci, ich schaue da mal rein!
Vielleicht kann mir jemand kurz erklären,
wie man in der neuen Beta die Akustik-Simulation verwendet.
Leider kenne ich mich damit bis jetzt nicht aus.
Danke!
Werd ich ausprobieren.
Bleibt alle gesund!
Leute, vielen Dank!
Wenn ich am Wochenende Zeit habe, werde ich mal etwas rumprobieren.
Danke und bleibt gesund!
Ich möchte eine Mandoline mit Pickup anschließen.
Bei den Einstellungen hab ich den Amp und die Cab mal deaktiviert. Das bringt aber vorallem eins: einen deutlich leiseren Sound.
Gibt es da jemand, der mit Mandoline am Kemper Erfahrungen hat?
Gabs dieses Problem nicht schon immer?
Following
Connect the Kemper‘s Main outs additionally with your Komplete Audio Input 1 & 2.
So you have direct monitoring and you can use the S/PDIF for recording.
I do it that way with Cubase and it works well.
Mimiq doubler effect please!