Thanks for this!
I have a question.
Say I made a new combined profile with the merge method, can I swap out the cab of an old profile with the new cab and have perfect separation as well?
Thanks for this!
I have a question.
Say I made a new combined profile with the merge method, can I swap out the cab of an old profile with the new cab and have perfect separation as well?
I have question.
Mr.Kemper did you make any KPA factory DI profiles for testing and comparing.?We need comparison with yours profiles.
Thank you.
Thanks for this!
I have a question.
Say I made a new combined profile with the merge method, can I swap out the cab of an old profile with the new cab and have perfect separation as well?
I have question.
Mr.Kemper did you make any KPA factory DI profiles for testing and comparing.?We need comparison with yours profiles.
Thank you.
CKemper asked us to post questions in new threads, not in this one.
CKemper asked us to post questions in new threads, not in this one.
Paul, that's not the way I read it. He said separate posts ...
It looked to me like was asking people to make new threads, so he could address each issue one by one. But, you may be right....
Agree with Larry. I got Eng. Kemper asked to ask specific single questions per post.
Let's see
USB Storage is not recognized in FW 2.8.0.10548.
* The usb storage device is recognized on FW2.7.3, and I updated to FW 2.8.0 using the usb storage device.
* I was able to downgrade to FW2.7.3 using the usb storage with "<" and ">" key boot method.
* When I connected the usb storage on the Front USB connector, "USB Storage" is not shown on display.
* I tried other usb storage, it is same result.
* I tried Maintenance Mode, the USB Stick test result did not change "checked mark" when I connected.
Please advice me.
Thank you.
usb import + export works for me on 2.8
USB did't show on my profiler too. (On 2.8).
Downgraded to 2.73 and all was ok again.
How about others?
It works here. I could export a Rig and import some others without problems.
I had problems with USB as well. Went back to 2.7.
bit strange that not all of us have that problem
Thank you for response.
The Problem has occurred in Front USB connector, Back USB connector is fine.
So, Rig Manager 1.2.3 works fine, import and export.
However, usb storage is not shown display, so I can not import cabinet date that is made by CabMaker 2.0.
Thank you.
Thanks for this!
I have a question.
Say I made a new combined profile with the merge method, can I swap out the cab of an old profile with the new cab and have perfect separation as well?
You can, but you will have the CabDriver algorithm be involved, anytime you grab a Portion of an old profile. However, the result will be very pleasing.
Beside a regular Studio Profile there is three possible elements that are fully authentic: a Direct Profile (Amp), a Merged Profile (Amp and Cabinet), and an imported impulse responce (Cabinet)
i tried old profiles with a new cab of mine yesterday...worked much better than swapping cabs before. I would say sounds like old profiles connected to real cab. Not perfect but really really good
i tried old profiles with a new cab of mine yesterday...worked much better than swapping cabs before. I would say sounds like old profiles connected to real cab. Not perfect but really really good
The CabDriver algorithm is active whether the Cabinet is ON or OFF...correct?
I have question.
Mr.Kemper did you make any KPA factory DI profiles for testing and comparing.?We need comparison with yours profiles.
Thank you.
We will have new profiles. However, I cannot imagine how they can serve as a comparison. (?)
i cant answer that
We will have new profiles. However, I cannot imagine how they can serve as a comparison. (?)
Ok. Forget about it
I just only tried.
If you have Factory rig for 2.7.3. fw I can´t wait new Factory DI Rig.
I sold my all gear,I could to buy KPA. I spend my all money !!!
The CabDriver algorithm is active whether the Cabinet is ON or OFF...correct?
From the wiKPA:
Quote[[ckemper]] There are two ways to bypass the cabinet section and activate what we call CabDriver: use "MonitorCabOff" to globally bypass the virtual cab for the mono monitor output only, while the full studio sound is still delivered. Or switch off the cabinet section directly. The latter has no sonic benefit, it delivers the same sound, but stereo to the main outs as well.
HTH
Ok. Forget about it
I just only tried.
If you have Factory rig for 2.7.3. fw I can´t wait new Factory DI Rig.
I sold my all gear,I could to buy KPA. I spend my all money !!!
If your issue is the money, I'm pretty sure there will be a ton of free profiles taking advantage of this new feature