Pedal getauscht - läuft!
Posts by janus
-
-
Sorry, alte Gewohnheiten. Gemeint ist Performance.
Ich bin in einer Performance und kalibriere unter System über "Pedal 6 init" das Volumenpedal, welches als Pedal 6 angeschlossen ist. Alle anderen Pedale sind "off".
Im Rig-Menü 3/5 ist das Pedal unter Location als Pre Effects und Range -4,9 eingestellt. Das bringt mir das Volumen von nahezu Null bis Voll, je nach Pedalstellung. Funktioniert!
Ich speicher die Performance ab, schalte aus, warte 10 Sekunden, schalte ein, bin in der Performance und die Einstellungen stimmen bzw. die Funktion stimmt nicht mehr.
Unter System Pedal 6 sehe ich im Verlaufsbalken CC07 des Pedals, dass es nur bis ca. 60% zurückgeht, anstatt 0? -
Moinsen,
Frage an die Pedal-Päpste
Ich hab´ ein Dunlop DVP Volumenpedal an der Remote an "Pedal 6".
Ich kann dies kalibrieren über "System - Pedal 6 Init". Ok. Funktioniert.
Die Einstellungen sind dabei egal, ob Pre- oder Post Effekt spielt dabei keine Rolle. An einem Sound habe ich das Volumen nach dem Amp, vor den Effekten. Also komplette Verzerrung von leise - Range -4,9 - bis laut.
Ich speicher (im Performance Mode) die Bank ab, beim nächsten Neustart muss ich das Pedal wieder kalibrieren. Es behält in keiner Perfomance die kalibrierten Einstellungen.
DAU?
-
-
Thank you very much.
-
After 3 Month of waiting, i played a gig last Saturday with the Remote.
We played for about 4 hours. 9 PM to 2 AM, with breaks between the sets.
Had not a single issue with it. Mounted the remote with a Dunlop Pedal on a Palmer PedalBay. One Cable from the Remote to the KPA.
"Accidently" i pushed the buttons real heard a few times. No problem for the Remote!
The reaction of the buttons is real good. You place your foot over the button and a soft step is enough to switch sound.
In Performance Mode the LED for the engaged Slot lights up bright white, while the other LEDs are a little bit darker. Perfect to locate your Switches when the lights get off.
The only thing that requires some practice, is the Layout of the Program-Up/Down Buttons. I would like them the other way round. But that´s the only complaint for me.
Thumbs up! -
Don´t know for sure, but...
The blue button is the Pre-Listening. So i guess you will hear the sound from both. The DAW and the AMP.
Maybe try to keep the Pre-Listening on and Mute the Track?! -
Wow! Thanks a lot for These free profiles Profiles.
-
Nice blog skyhigh
-
Hopefully it is still there
-
Great. Thanks a lot. Hope it will fit to some Boston-Tunes.
-
I haven't read the specs, but I'd be hesitant to use anything calling itself a 'speaker simulator'. It needs to be a clean but attenuated signal going in to the KPA, not a coloured one.
Cheers,
Sam
The PDI-03 has 4 unsimulated Line-Outs -
How about the Palmer PDI-03 or PDI-05?
http://www.palmergear.com/images/manuals/pdi03.pdf</a>
http://www.thomann.de/gb/palmer_pdi_05.htm -
Ahh, i guess John Huldt is as cool and nice as the kemper staff. I think it´s important to take oneself not too seriously.
-
-
The Box for Direct Profiling with Firmware 3.0?!
-
Really?
I don´t know yet.
Maybe i drill some holes in the PedalBay and use the Screwholes from the Remote´s Rubber Feet with that http://www.thomann.de/de/harley_benton_mounties.htm . If this is a warranty issue with Kemper than i will use some Velcro. -
Yes, on both sides about 2cm. But both, the pedalbay and the FCB - which was fixed on the palmer - suited in the bag.
The Remote and one Expressionpedal should fit nicely on that one with about 1,5cm left on both sides. That was my purpose to buy it, not knowing the size
I hoped it would fit (corrected the link). -
I will go with this one:
http://www.thomann.de/de/palmer_mi_pedalbay_60.htm
Bought last year and did one gig with it (FCB 1010 on it). It´s ok for me and well built with a nice Gigbag. -
Using it for almost a few years now without any problem except some channel crossing with other musician. Last year we started to play a smaller location and there i ran in trouble.
Got some dropouts. We investigatet the place and our only conclusion is that this location is studded with WLAN-Hotspots. The G30 works around 2,4GHz like the most WLAN´s.
So be careful with WLAN´s around. Don´t know if it works the same with the G30. With the Mics from Line6 you can leave the Mic off and only the receiver is on. So you can switch trough all chanels and see were the biggest indefferences are. I would recomend a view into the manual.